New Conductive Epoxy Primer

September 15, 2016

Epoxy.com is proud to announce Product #659. This is a  conductive primer that makes our existing conductive epoxy topcoat products even better.  Here is summary of the material:


CONDUCTIVE EPOXY PRIMER

Epoxy.com Product #659


DESCRIPTION

Product #659 Conductive Epoxy Primer is a water-based, two component, carbon filled conductive epoxy primer designed for use with various Epoxy.com Conductive Systems.Product #659  has very low odor making it suitable for use in occupied buildings.

ADVANTAGES

  • For Use with Various Epoxy.com Conductive Systems
  • Maintains Electrical Conductivity Performance over the Wear Life of the System
  • Fast Dry Time
  • Low Odor During Application and Cure
  • VOC Compliant in all 50 US States, Meets USGBC LEED Requirements

CONSIDERATIONS

  • Substrate must be above 50°F and relative humidity below 85% for proper curing.
  • Substrate must be properly prepared following Epoxy.com recommendations and free of dirt, waxes, curing agents and other foreign materials
  • Excessive moisture in the substrate will require a moisture vapor control treatment like Product #830
  • Concrete substrate must be insulated with a non-conductive
    epoxy primer/base coat like Product #12 Chemical Resistant Epoxy Primer or Product #899 Epoxy Primer  prior to application of Product #659 Conductive Epoxy Primer. Consult with Epoxy.com Technical Department for recommendations.
  • Must be top coated with a conductive top coating like Product #1ESD, or Product #630 Conductive.

APPLICATION

SURFACE PREPARATION

Surface Preparation is the most critical portion of any successful resinous flooring system application. All substrates must be properly prepared and tested for moisture as outlined in installation procedures or as recommended by Epoxy.com.

BATCHING, MIXING & INSTALLATION

 

Product #659 Conductive Epoxy Primer:
PART A 1 quart to
PART B 3 quarts to
Clean Water 8 volume ounces (6% by volume of water)
Total 4.125 quarts

Coverage (250 square feet/gal.) 265.6 square feet per batch

Pre-mix Product #659 Conductive Epoxy Primer  part B prior to combining with part A. Mix 1 part A with 3 parts B for 2-3 minutes with a low-speed jiffy mixer, scraping sides and bottom of mix vessel. Continue mixing and add 6% by volume clean potable water and continue mixing for 1 additional minute.

Immediately spread and back roll mixed Product #659 Conductive Epoxy Primer at a rate of 250 ft2 per gallon with a short nap roller over previously applied non-conductive epoxy primer/base coat.Care should be taken to avoid puddles. Allow to cure minimum 12 hours (at 75°F) to maximum 24 hours before coating with specified topcoat.

Important: Test Product #659 Conductive Epoxy Primer with ohm meter prior to top coating to confirm acceptable level of conductivity is achieved. If test readings are higher than 25,000 ohms, contact Epoxy.com Technical Support Department for further instructions before installing specified topcoat.

Top Coat with a conductive top coating like Product #1ESD, or Product #630 Conductive.

CLEAN-UP

Clean skin with soap and water. Tools and equipment should be cleaned with warm soapy water, xylene or lacquer thinner. Consult Material Safety Data for safety and health precautions.

COMPOSITION

Waterborne Epoxy Resin and Conductive Filler. Color: Black.

COVERAGE

Product #659 Conductive Epoxy Primer applied at 250 ft2 per gallon yields 2.7 mils dry film thickness.

TECHNICAL DATA (@ 75°F, 50% RH)

Viscosity 500-1000 CPS
Mixing Ratio 1 Part A to 3 Parts B by Volume
Solids Content, by volume 45%, thinned
Volatile Organic Content (VOC) <10 g/L
Bond Strength to Concrete 300-400+ psi (100% concrete failure)
Shelf Life 6 months when properly stored

CURE/DRY TIME (@ 75°F, 50% RH)

Pot Life 20-30 minutes
Dry to Touch 6-8 hours
Recoat (Refer to testing requirements) 12-24 hours
 Light Traffic 24 hours

For more information, visit us on line at Epoxy.com, email me at norm@epoxy.com or call Epoxy.com Technical Support at 352-533-2167.

Please join us on Facebook and Twitter.


Seamless Epoxy Flooring Systems Explained

August 15, 2016

Epoxy.com offers many different types of seamless flooring. We offer so many kinds that sometimes it confuses people. The purpose of this article is to explain the differences, and to help you choose the right epoxy seamless flooring system for your application. In some cases the right seamless flooring system will not even be an epoxy. It may be polyurethane or Methyl Methacrylate (MMA).

Epoxy.com Epoxy Chip Flooring in VT rest area.

Epoxy.com Epoxy Chip Flooring on a VT Interstate Rest Area – Taken over 15 years after installation.

Epoxy Floor Coatings

Epoxy coatings can be effective flooring systems. When choosing epoxy as a flooring system choose a 100% solids (zero VOC, hard durable coating. You also want a coating that is available in multiple colors. These floor coatings can last for decades, so you want to pick a color that you like. Properly installed you will be looking at this floor coating for a very long time. This kind of flooring system is available in the following options:

  1. Epoxy.com Product #1 – www.epoxy.com/1.htm – meets all the criteria above. It has good chemical resistance, and excellent cost to benefit ratio. Great for warehouses, in areas with high traffic and only modest chemical exposure.
  2. Epoxy.com Product #1ESD – www.epoxy.com/1esd.aspx. This is the same as product #1 above but has conductive filler in it. Depending on the primer you use under this system it can be conductive (100,000 – 1,000,000) ohms of resistance or Electro-Static Dissipative (ESD) which is 1,000,000 to 1, 000,000,000 ohms. Used in plants that produce explosive materials like ammunition, fireworks, flairs, or explosive solvents, and used in areas of sensitive electronics, like computer server buildings, avionics, electronics assembly and electronic production areas.
  3. Epoxy.com Product #2 – www.epoxy.com/2.aspx. This is similar to product #1 but with a much higher chemical resistance. This major increase in chemical resistance is offset by only a small increase in the cost of the #2 over the Product #1. The product #2 is well suited for applications like garages, machine shops, sewer tank floors, battery rooms, cooling towers, grooming shops, dog kennels and all areas where an economical chemical resistant coating is required.
  4. Epoxy.com Product #633 – www.epoxy.com/633.aspx – is a highly chemically resistant epoxy floor coating and flooring system. Like Product #1 and Product #2 is extremely durable. Product #633 is typically used in areas where containment of aggressive chemical is imperative. For example Product #633 will hold up to continuous exposure of 98% Sulfuric acid for a period of at least 6 months without loss of structural integrity. Great for secondary containment for a large number of chemicals.

     

All the systems above can go over many different types of substrates with the proper surface preparation. All of the products above are available in 17 colors and can be color matched for an additional cost. The systems above can be combined with various anti-skid materials or broadcast with silica broadcast aggregate to produce a thicker floor.

 

Chip Floor

Epoxy.com Chip Flooring – www.epoxy.com/chips.aspx – is the perfect blend of economy, durability, low maintenance, and gorgeous appearance. It uses a 100% solids pigmented epoxy base coat, a full broadcast of plastic chips, and two coats of chemical resistant clear glaze. The chemical resistant glaze also makes this easily the most non-yellow epoxy top coat available today. This easy to clean chip flooring system is best for high traffic areas where appearance, durability and low cost of ownership is a must. Chip Flooring is great for commercial and residential kitchens, bathrooms, showers, grooming shops, kennels, veterinary clinics, garage floors, show rooms, rest areas, and much more. This product can be installed with an integral cove base. Epoxy.com Chip Flooring can be installed by a contractor but easy enough to be installed by a home owner. Epoxy.com Chip Flooring can be installed in a residence but is rugged enough to be used in the most demanding commercial applications.

Quartz Flooring

Quartz Flooring Product #15 – www.epoxy.com/15.aspx has a long history of being durable, attractive and non-yellowing. I personally installed this product on high school bathroom floors in the mid 70s. These floors have held up to the test of time with little or no wear, little or no loss of shine and little to no yellowing even under the urinals. This is also available with an integral cove base

Solid Colored Flooring

These solid colored floors are based around self leveling, trowelable or double broadcast application techniques. These floors are sometimes called shop floor. They are made to be thick and extra durable under extremely harsh environments. They can be top coated with any of the systems above under coatings. This kind of flooring is available in 3 speeds of cure: normal, fast, and cold cure. Solid colored flooring is also available with an integral cove base.

Methyl Methacrylate (MMA) Flooring

The big advantage of MMA is speed of curing. Each coat of MMA will cure hard to the touch in 1-2 hours. This allows the next layer to be applied quickly and traffic to be returned to it quickly. You can even build a fast setting integral cove out of MMA resin.

I personally installed MMA on many floors with very tight schedules. One restaurant was only closed for breakfast. The project started with rotten plywood floors. At 10 PM the carpenters came in to work. They removed rotten floor and floor joists. They replaced the floor joists and the plywood. At 5 AM we went in with the flooring installation crew.  We primed the floor and sealed up the joints in the wood and the screw holes. At 6:30 AM we laid the floor. At 8 we put a glaze coating on the floor and by 10:30 the restaurant workers were on the floor prepping for lunch. The floor installation from start to traffic took just 5.5 hours.

Polyurethane Decking Systems

Polyurethane Decking – http://www.epoxy.com/elastomeric.aspx – is the system best used in areas where maximum flexibility is necessary. This is typically outdoors, waterproof applications like balconies.

Specialized Flooring

We have a number of systems that are specialized flooring like conductive and ESD (Electrostatic Dissipative) flooring – www.epoxy.com/conductive.aspx – and various hybrid systems. If your project does not seem to fit in the categories above email me at norm@epoxy.com or call us at 352-533-2167.

 

In conclusion we offer many types of seamless flooring systems, they can be used for commercial and residential applications. These systems are durable, economical, and easy to install even by homeowners. These seamless flooring systems may be made out of epoxy, polyurethane, or methyl Methacrylate (MMA). Seamless flooring systems are available in multicolored or solid colored. They range in chemical resistance from very good to resistant to aggressive chemicals. When in doubt what is right for your project send me an email at norm@epoxy.com or give me a call at 352-533-2167.


Applying New Epoxy over Old Epoxy

February 13, 2015

I frequently get calls and emails from folks who want to install our epoxy over an existing epoxy floor or coating that they have. They want to know if it is okay to go over it and what they have to do to properly prepare the surface.

If the existing epoxy is a good hard solid one that is well bonded to a well prepared substrate it is possible. On the other hand if you are replacing it, what is wrong with the existing epoxy? Has the existing epoxy been badly abused by heavy sharp objects being dragged on it? Was the exiting epoxy damaged by chemicals beyond the chemical resistance of the existing epoxy? Are you just trying to upgrade the look of the existing epoxy?

You should be concerned about going over epoxy that is coming loose from the substrate. That may mean that there was poor surface preparation. It may also mean that the quality of the epoxy might not be what it should be. You need to be concerned about epoxy that is wearing out. If it is wearing out you want to know why. My company and I personally started out as installers of epoxy. I have never seen or been made aware of any of Epoxy.com coatings and/or flooring systems that have worn out have come loose from the concrete. I have seen concrete so pounded by traffic that it came loose, but our epoxy was still attached and still doing its job. That is based on over 30 years of field experience with the products.

Back to the question, “can I put epoxy over epoxy?” I always assume that the reason that the epoxy is wearing out or coming loose is that the epoxy is low quality or the installation was poorly done or both until I can prove otherwise. The way that I do that is to attempt to grind or shot blast off the existing epoxy. If after a substantial effort the epoxy cannot be removed and I cannot hear a hollow sound under the existing epoxy, I feel I have proven that the existing material is solid and well bonded.

Let’s take a moment to discuss that dreaded hollow sound above. If the flooring system or coating is very poorly bonded you will get a sound from your grinder like you are dragging a piece of paper or a piece of stone under the grinder, or rubbing stone. When you tap it with a hammer you get a hollow higher pitch noise than you get when you tap solid concrete or a solid floor over concrete.

You must be sure that the substrate is free of all types of contamination, including but not limited to oil, grease, food fats, curing compounds, sealers, laitance, dirt, wax etc. The existing epoxy left behind must be well bonded, and sanded until it has no shine. See Epoxy Surface Preparation Procedures for more information on this subject.

The beauty of trying to get it off is you are removing all the shine and getting it ready to accept another layer of epoxy. Just before I install the new layer of epoxy I solvent wipe with xylene, let it dry. Then I recommend a coat either Epoxy.com Product #899 Primer or Epoxy.com Product #12 Chemical Resistant Primer. Then install epoxy as usual. For more surface preparation and installation tips please visit or “Where to Start” page at: http://www.epoxy.com/start/default.aspx

Related Resources on Epoxy

Where to Start” page may be the best way to get you off to a quick start.

Epoxy Coatings

Epoxy Primers and Sealers

Chemical Resistant Epoxy

Epoxy Chemical Resistance Chart

www.epoxy.com

Epoxy.com Technical Support
Norm Lambert, President – Technical Support Director
352-533-2167
info@epoxy.com

 

 

 


Seamless Epoxy Flooring Systems Explained

August 25, 2014

Epoxy.com offers many different types of seamless flooring. We offer so many kinds that sometimes it confuses people. The purpose of this article is to explain the differences, and to help you choose the right epoxy seamless flooring system for your application. In some cases the right seamless flooring system will not even be an epoxy. It may be polyurethane or Methyl Methacrylate (MMA).

Epoxy.com Epoxy Chip Flooring in VT rest area.

Epoxy.com Epoxy Chip Flooring on a VT Interstate Rest Area – Taken over 15 years after installation.


Epoxy Floor Coatings

Epoxy coatings can be effective flooring systems. Using Epoxy as a flooring system you need a 100% solids, zero voc, hard durable coating. You also want a coating that is available in multiple colors. These floor coatings can last for decades, so you want to pick a color that you like. Properly installed you will be looking at this floor coating for a very long time. This kind of flooring system is available in the following options:

  1. Epoxy.com Product #1 – www.epoxy.com/1.htm – meets all the criteria above. It has good chemical resistance, and excellent cost to benefit ratio. Great for warehouses, in areas with high traffic and only modest chemical exposure.
  2. Epoxy.com Product #1ESD – www.epoxy.com/1esd.aspx. This is the same as product #1 above but has conductive filler in it. Depending on the primer you use under this system it can be conductive (100,000 – 1,000,000) ohms of resistance or Electro-Static Dissipative (ESD) which is 1,000,000 to 1, 000,000,000 ohms. Used in plants that produce explosive materials like ammunition, fireworks, flairs, or explosive solvents, and used in areas of sensitive electronics, like computer server buildings, avionics, electronics assembly and electronic production areas.
  3. Epoxy.com Product #2 – www.epoxy.com/2.aspx. This is similar to product #1 but with a much higher chemical resistance. This major increase in chemical resistance is offset by only a small increase in the cost of the #2 over the Product #1. The product #2 is well suited for applications like garages, machine shops, sewer tank floors, battery rooms, cooling towers, grooming shops, dog kennels and all areas where an economical chemical resistant coating is required.
  4. Epoxy.com Product #633 – www.epoxy.com/633.aspx – is a highly chemically resistant epoxy floor coating and flooring system. Like Product #1 and Product #2 is extremely durable. Product #633 is typically used in areas where containment of aggressive chemical is imperative. For example Product #633 will hold up to continuous exposure of 98% Sulfuric acid for a period of at least 6 months without loss of structural integrity. Great for secondary containment for a large number of chemicals.

     

All the systems above can go over many different types of substrates with the proper surface preparation. All of the products above are available in 17 colors and can be color matched for an additional cost. The systems above can be combined with various anti-skid materials or broadcast with silica broadcast aggregate to produce a thicker floor

 

Chip Floor

Epoxy.com Chip Flooring – www.epoxy.com/chips.aspx – is the perfect blend of economy, durability, low maintenance, and gorgeous appearance. It uses a 100% solids pigmented epoxy base coat, a full broadcast of plastic chips, and two coats of chemical resistant clear glaze. The chemical resistant glaze also makes this easily the most non-yellow epoxy top coat available today. This easy to clean chip flooring system is best for high traffic areas where appearance, durability and low cost of ownership is a must. Great for commercial and residential kitchens, bathrooms, showers, grooming shops, kennels, veterinary clinics, garage floors, show rooms, rest areas, and much more. This product can be installed with an integral cove base. Epoxy.com Chip Flooring can be installed by a contractor but easy enough to be installed by a home owner. Epoxy.com Chip Flooring can be installed in a residence but is rugged enough to be used in the most demanding commercial applications.

Quartz Flooring

Quartz Flooring Product #15 – www.epoxy.com/15.aspx has a long history of being durable, attractive and non-yellowing. I personally installed this product on high school bathroom floors in the mid 70s. These floors have held up to the test of time with little or no wear, little or no loss of shine and little to no yellowing even under the urinals. This is also available with an integral cove base

Solid Colored Flooring

These solid colored floors are based around self leveling, trowelable or double broadcast application techniques. These floors are sometimes called shop floor. They are made to be thick and extra durable under extremely harsh environments. They can be top coated with any of the systems above under coatings. This kind of flooring is available in 3 speeds of cure: normal, fast, and cold cure. Solid colored flooring is also available with an integral cove base.

Methyl Methacrylate (MMA) Flooring

The big advantage of MMA is speed of curing. Each coat of MMA will cure hard to the touch in 1-2 hours. This allows the next layer to be applied quickly and traffic to be returned to it quickly. You can even build a fast setting integral cove out of MMA resin.

I personally installed MMA on one kitchen floor with a very tight schedule. The restaurant was only closed for breakfast. The project started with rotten plywood floors. At 10 PM the carpenters came in to work. They removed rotten floor and floor joists. They replaced the floor joists and the plywood. At 5 AM I went in with my crew and we primed the floor and sealed up the joints in the wood and the screw holes. At 6:30 AM we laid the floor. At 8 we put a glaze coating on the floor and by 10:30 the restaurant workers were on the floor prepping for lunch. The floor installation from start to traffic took just 5.5 hours.

Polyurethane Decking Systems

Polyurethane Decking – http://www.epoxy.com/elastomeric.aspx – is the system best used in areas where maximum flexibility is necessary. This is typically outdoors, waterproof applications like balconies.

Specialized Flooring

We have a number of systems that are specialized flooring like conductive and ESD (Electrostatic Dissipative) flooring – www.epoxy.com/conductive.aspx – and various hybrid systems. If your project does not seem to fit in the categories above email me at norm@epoxy.com or call us at 352-533-2167.

 

In conclusion we offer many types of seamless flooring systems, they can be used for commercial and residential applications. These systems are durable, economical, and easy to install even by homeowners. These seamless flooring systems may be made out of epoxy, polyurethane, or methyl Methacrylate (MMA). Seamless flooring systems are available in multicolored or solid colored. They range in chemical resistance from very good to resistant to aggressive chemicals. When in doubt what is right for your project send me an email at norm@epoxy.com or give me a call at 352-533-2167.


Epoxy.com Epoxy Material Calculators

June 20, 2012

Epoxy.com calculators are designed for busy professional estimators who wants to quickly and accurately calculate the amount of epoxy or epoxy like material for their job.

Epoxy Coating Spread Rate Calculator shows how much 100% solids epoxy coating  you will need for your installation.

Epoxy Dowel  Bar and Anchor Bolt Adhesive Calculator shows the amount of epoxy adhesive you will need to install dowel bars into concrete or wood.

Epoxy Stone Overlay Calculator figures the amount of epoxy adhesive resin your will need to do an epoxy stone overlay.

Epoxy Table Top Resin Calculator  figures the amount of epoxy table top resin you will need to do a table or bar top.

Epoxy Tile Grout Calculator is used to calculate the amount of epoxy tile grout that you need for a specific tile size and joint spacing.

Electrical Epoxy Calculator is used to calculate the amount of epoxy you will need to encapsulate electrical components.

Epoxy.com Conductive Flooring Calculator figures how much material you will need to install a conductive epoxy flooring system.

Is there another Epoxy.com product calculator that you would like to have here, send your suggestions to Norm Lambert – Epoxy.com Technical Director at norm@epoxy.com.


Epoxy Installation Terminology

June 8, 2012

Epoxy.com technical support staff gets asked a lot about epoxy terminology. This page deals with the terms associated with epoxy  installation times.  Specifically “Epoxy Pot Life” sometimes called the epoxy’s “Working Time“, “Tack Free Time“, “Initial Cure”,  and “Final Cure” sometimes called the epoxy’s “Full Chemical Cure“.  Keep in mind that all of the information below assumes that the epoxy has been properly measured and mix. The information is specificall based on Epoxy.com Products, but is typically true about many 100% solids epoxies.

Epoxy Pot Life aka Working Time

The “Pot Life” of epoxy is the time that it takes for it to start gelling in the in the mix vessel (typically a bucket). One important thing to remember is that this is done by a standard which is 200 grams of the material at a given temperature typically 70° F or 77° F. So remember that the bigger you make the  batch of Epoxy.com resin, the faster the batch will set.  See the Epoxy Pot Life Page for more details.

Epoxy Tack Free Time

The “Tack Free Time” of the epoxy is pretty much just what it sounds like.  It is the time that the epoxy is no longer sticky to the touch. When the epoxy is “Tack Free” it can be handle or even walked on if necessary, but you will want to be careful because the epoxy will be very vulnerable to scratching right after it becomes “Tack Free”. The “Tack Free Time” given on the product’s Epoxy.com technical data sheet is also at a specific temperature, typically 77°F.

Epoxy Initial Cure Time

The “Initial Cure” is not the same as “Tack Free“.  Typically “Initial Cure” is about twice as long as the Tack Free Time. Most epoxies have about 80% of the epoxy’s final cure at “Initial Cure“. After the Epoxy’s “Initial Cure” the epoxy is still vulnerable to scratching, but typically strong enough that these scratching will be strictly esthetic and not structural. In cases where time permits and esthetics are essential you may want to wait 1.5 to 2 times the “Initial Cure” of the epoxy before you allow heavy traffic or rougher handling. The primary outside force that can effect this time is temperature. The epoxy’s “Initial Cure” time assumes the temperature indicated on the technical data sheet, or 77° F. if not otherwise specified.

Final Cure aka “Full Chemical Cure”

When the epoxy has reached its “Final Cure” it has achieved the strengths indicated on the Epoxy.com technical data sheet. It also means that the epoxy has reached its full water resistance and full chemical resistance. This time also is also effected by temperature, similar to all the other times listed above. One interesting note is that “Final Cure” when the epoxy is 99% cured.  Epoxy will continue to harden for as much as a year.  So  the “Final Cure” for epoxy is like the “28 day” cure on concrete.  It is typically said that the concrete is fully cured in 28 days.  In fact concrete will under the right conditions continue to cure for up to 100 years.

For more information email me at
norm@epoxy.com
  or visit Epoxy.com “Where to Start” Page for more information.

Norm Lambert
President & Director of Technical Support
Epoxy Systems, Inc Florida & Vermont USA
Available by Phone M-F 9AM-4PM Eastern Time (6 AM – 1 PM Pacific Time)
352-533-2167 (Voice)
352-465-3497 (fax)
norm@epoxy.com
www.epoxy.com
New Secure Login www.epoxy.com/wireless Now Available on your web enabled  Wireless Devices

Subscribe to Epoxy.com News Feed – Get the latest product information, tricks and tips delivered directly to you via your favorite news reader.


New Epoxy.com Electro Static Dissipative Epoxy

September 1, 2010

Epoxy.com announces a new ESD Epoxy Product

New Epoxy Electrostic Dissipative (ESD) Epoxy Coating

Less Expensive, Easier to Use, More Durable


Epoxy.com Product #677

Electro Static Dissipative (ESD) /CONDUCTIVE COATING


DESCRIPTION

Epoxy.com Product #677 is a pigmented, water-based epoxy coating designed to achieve either an electro-static dissipative (ESD) finish or conductive finish by
modifying the underlying system components and thickness. Epoxy.com Product #677 has very low odor making it suitable for use in occupied
buildings and has high bond strength and adhesion to concrete and other surfaces.

ADVANTAGES

  • Durable, Attractive, Chemical Resistant, Non-Porous, Light Reflective Finish.
  • Low Odor during application and cure.
  • Maintains Electrical Conductivity Performance over the Wear Life of the System
  • Fast Dry and Re-coat Time.
  • Easy Clean-up.
  • Provides an ESD finish in the range of 1,000,000 to 1,000,000,000 ohms resistance when used over a non-conductive
    primer/basecoat or a conductive finish in the range of 25,000 to 1,000,000 ohms resistance when used over a conductive primer/basecoat.

CONSIDERATIONS

  • Substrate must be above 50°F and relative humidity below 85% for proper curing.
  • Substrate must be free of dirt, waxes, curing agents and other foreign materials.
  • Excessive moisture in the substrate will require a moisture vapor control treatment.

TYPICAL USES

Concrete floors and walls in electronic component assembly areas, data processing, military/aerospace, pharmaceutical plants,
hazardous industries (dust or explosion hazards). For use in any areas where the build-up of static electricity is a concern or a spark-proof floor is required.

APPLICATION

SURFACE PREPARATION

Surface Preparation is the most critical portion of any successful resinous flooring system application. All
substrates must be properly prepared and tested for moisture as outlined in Epoxy.com
Surface Preparation Guidelines.

INSTALLATION

Mix Part B of Epoxy.com Product #677 prior to combining. Mix 1 part Part A with 2 parts Part B. Epoxy.com Product #677 at a rate of 200 ft2
per gallon per coat with a short nap roller. Care should be taken to avoid
puddles. Two coats are necessary to insure uniform coverage.

Epoxy.com Product #677 Thin-Film ESD Epoxy Coating System 12-15 Mils(1,000,000-1,000,000,000 ohms)

Material Qty./ 1000 SF Coverage
1. Epoxy.com Product #899 Epoxy Primer 4-5 gallons 200-250 SF /gallon
2. Epoxy.com Product #677 ESD/Conductive Epoxy Coating 5 gallons 200 SF /gallon
3. Epoxy.com Product #677 ESD/Conductive Epoxy Coating 5 gallons 200 SF /gallon

CLEAN-UP

Clean skin with soap and water. Tools and equipment should be cleaned with warm soapy water, xylene or lacquer thinner. Consult Material Safety Data for safety and health precautions.

COMPOSITION

Waterborne Epoxy Resin and Conductive Fillers

COVERAGE

Epoxy.com Product #677, when applied at 200 SF per gallon, yields 5.2 �to 6.0 mils dry film thickness.

TECHNICAL DATA

Viscosity @ 75°F 600-1000 CPS
Mixing Ratio 1 Part A to 2 Parts B by Volume
Solids Content, by volume 50-55%
Volatile Organic Content (VOC) <20 gm/L
Bond Strength to Concrete 400-500 psi (100% concretefailure
Weight per Gallon, mixed 8.75-9.00 pounds per gallon, mixed

CURE/DRY TIME

Pot Life 20-30 min.
Dry to touch 6 hours @ 75°F
Recoat 8-24 hours @ 75°F
Light Traffic 24 hours @ 75°F
�H� Hardness 2 days
�5-H� Hardness 30 days

AVAILABILITY

Contact Epoxy.com Customer Service Department at 321-206-1833

Maintenance

Remove animal fats, oil, grease or soap film promptly to reduce slipperiness. Epoxy.com Product #677 can be cleaned with neutral soaps and detergents.
If long periods of heavy traffic cause wear patterns reapply as need.
Anti-skid materials will reduce the effectiveness of the static dissipative
properties of this material.  Do not use aggressive anti-skids. It is
impossible to get an accurate reading of the conductivity of the floor if
anti-skids are used.

Technical Services

Contact Epoxy.com Technical Support with your questions about this
product at 352-533-2167. Epoxy.com Technical Support Department can help you
with the selection, specification, installation, and maintenance of
Epoxy.com products, or visit http://www.epoxysystems.com.

Norm Lambert
President &
Director of Technical Support
Epoxy Systems, Inc
Available by Phone M-F 9AM-4PM Eastern Time (6 AM – 1 PM Pacific Time)
352-533-2167 (Voice)
352-465-3497 (fax)
norm@epoxy.com

 [Home]
[Catalog of Products]
[Where to Start]
[Bonding Systems]
[Chip Floors]
[Chemical Resistance]
[Coatings]
[Conductive]
[Applications]
[Elastomeric Polyurethane Systems]
[Garage
Floors
] [High Temperature]
[Industrial Floors]
[Injection]
[Joint Systems & Sealants]
[Mortars / Grouts]
[Novolac]
[Polymer Systems]
[Primers Sealers]
[Misc.] [Seamless Flooring]
[Waterproofing]
[Dealers Wanted]
[Installation Tips]
[Product Guide]
[Wood Filler]
[Who We Are]
[Guide Specs]
[Tech Data Sheets in Acrobat Format]
[MSDS in Acrobat Format]


%d bloggers like this: