” for tile installations? I don’t want one of those so called ‘epoxy tile grout’ that uses water based epoxy and Portland Cement combination. I want it to be a true epoxy system. If so please provide me a product data sheet.”
Epoxy.com Product #225
Water Cleanable Epoxy Grout and Adhesive With Filler
100% Solids Epoxy and Special Fillers – Water Cleanable – No Portland Cement Content
Epoxy.com Product #225 Water Cleanable Epoxy Tile Grout and Adhesive is a user friendly, water cleanable, 100% solids epoxy grout and adhesive and Filler Powder . Used for grouting ceramic tile, brick pavers, and stone, Epoxy.com Product #225 Water Cleanable Epoxy Tile Grout and Adhesive is supplied in pre-packaged kits containing resin, hardener, and mineral fillers that produce a dense, uniform seal. Typical applications for Epoxy.com Product #225 Water Cleanable Epoxy Tile Grout and Adhesive require resistance to thermal shock, chemicals, and heavy traffic including meat packers, breweries, canneries, bottlers, CIP areas, and pharmaceutical formulators.
- User Friendly Packaging
- Low Odor for use in Occupied Areas
- Meets ANSI A-118.3 Specification for Chemical Resistant, Water Cleanable Epoxy Grout
- Available with Cold-Room Hardener
- Low Viscosity-good wetting properties
- Versatile-for both Setting and Grouting all Types of Tile
- USDA Approvable
- Available in Floor Grade and in Wall Grade
- Zero (0) VOC – No VOC content means it meets the strictest Low VOC requirements
Surface Preparation is the most critical portion of any successful resinous flooring system application. Work must be performed by trained or experienced contractors or maintenance personnel. Epoxy.com service department is pleased to answer any questions. Before grouting, clean joints and the tile surface with a damp sponge to remove dust, dirt, and other contaminants. Do not leave water standing in joints. Do not clean tiles with acid cleaners.
Empty entire contents of Epoxy.com Product #225 Water Cleanable Epoxy Tile Grout and Adhesive Part A and Part B into a clean mixing pail. With a slow speed drill or margin trowel, mix until liquids are completely blended. Add at least ¾ of the TILE GROUT FILLER (more for wide joints) and blend until uniform.
- Substrate must be free of dirt, waxes, curing agents, and other foreign materials
- Protect from exposure to chemicals and harsh cleaners until fully cured.
- Substrate temperature must be a minimum of 50°F-Contact Epoxy.com for Low Temperature Cure
Pour mixed Epoxy.com Product #225 Water Cleanable Epoxy Tile Grout and Adhesive onto working area. Following standard epoxy and grouting techniques, apply to surface. Be sure all grouted joints are completely filled. Remove excess grout with grout float. Do not leave excess grout on face of tiles. For complete installation instructions, contact Epoxy.com Technical Service.
Some tiles and pavers can be stained by color pigments in Epoxy.com Product #225 Water Cleanable Epoxy Tile Grout and Adhesive. Try small area to determine results before grouting entire surface.
Clean skin with soap and water. Tools and equipment should be cleaned with xylene or lacquer thinner. Consult Material Safety Data for safety and health precautions.
Epoxy.com Product #225 Water Cleanable Epoxy Tile Grout and Adhesive is a100% Solids Epoxy Adhesive and Grout Fillers
|Tensile Strength||ASTM C-307||2,000 to 2,500 psi|
|Compressive Strength||ASTM C-579||15,000 psi|
|Flexural Strength||ASTM C-580||3,800 to 4,100 psi|
|Water Absorption||24 hours||0.15%|
|Heat Resistance||160°F Continuous
|Bond Strength to Concrete||ASTM C-321||350-400 psi|
|Working Life||45 minutes|
|Initial Cure||6-7 hours @ 75°F|
|Full Set Time||Overnight|
|Full Cure & Maximum Resistance||5-10 days|
After completing the application of Epoxy.com Product #225 Water Cleanable Epoxy Tile Grout and Adhesive, the installer should provide the owner with maintenance instructions. If floors become slippery due to animal fats, oil, grease, or soap film, clean and rinse thoroughly. Epoxy.com Product #225 is easily cleaned with neutral soaps or detergent
Epoxy.com Product #225 Water Cleanable Epoxy Tile Grout and Adhesive is available in custom colors, subject to laboratory approval, minimum quantity, lead time for production, and increased cost.
Click the picture of color card below for a larger version of this picture of the color chart.
Please note: The picture to the right is a photographic reproduction of the color card for this product. The photo reproduction process and your monitor and/or printer will change these colors. This chart is to give you an idea of the colors available and not intended for critical color selections.
Need help figuring out how much Epoxy.com Product #225 Water Cleanable Epoxy Tile Grout and Adhesive you will need. Use the Epoxy.com Product #225 Grout Calculator.
Glass Tile Mural – Close Up
Madagascar Exhibit at the Bronx Zoo in NY
Mural and Pictures by: Jeannie Egel
Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12Noon-1PM Eastern Time for Lunch.
321-206-1833 Customer Service – Ordering and Order Status
Katey Fontaine, VP – Customer Service Director
714-657-3826 Technical Support
or Norm Lambert, President – Technical Support Director
352-489-1666 Accounting and Administration
Debby Lambert, CEO, and CFO
352-489-1625 Fax line to all Departments