Extending The Epoxy Install Season

October 17, 2017

Cold Temperature Epoxy

Installing Epoxy on Garage Floors in Cold Temperatures

Extend Epoxy Installation Season into Winter

It is that time of year again when I start getting  a lot of calls and emails about installing epoxy in cold temperatures. epoxy_color_chart_s

The best time to protect your floor is before it sees any salt at all. If you have a new garage floor now is the time to protect it.  It is still possible to do older floors but the more salt it sees the more difficult and expensive it can be.

The night temperatures are dropping this time of year. It is still possible to coat your garage floor before temperatures drop too low. Our cold temperature epoxies will cure with substrate temperatures as low as 35 degrees F, although it will set a lot faster at 40 degrees F.

Protecting your garage floors is especially  important in areas that will see salt from roads or ocean spray.  You will want to protect your garage from the ravaging effects of salt deterioration. Without protecting your floor salt will damage your garage floor and make for very expensive repairs later if it is not well protected.

It is not too late to protect your floor even in cold climates if you move quickly now.  Without this protection your garage floor will not be as nice come spring as it is now.  The damage that takes place is not only aesthetic but structural.

Cold Temperatures Epoxies

Cold Temperature Cure Epoxy Resins allow installation to be done at low temperatures as low as 35°F., (although it sets a lot faster at 40°F) expanding your epoxy coating and epoxy flooring installation season. Epoxy.com Cold Temperature Cure Epoxy Resins can also be used in cold storage areas like food processing areas, where the temperature cannot be raised higher than 35° F or so. Normal cured epoxy typically requires 50°F or more.

Depending on how you mix the aggregate into the products below, they can be used as a mortar for overlays, or a grout for sealing between other hardened construction materials.

Commonly Used Cold Temperature epoxies

Product #1 Cold Temperature Cure Epoxy Coating is 100% solids and specially formulated coatings for cold temperature applications. Cold Temperature Epoxy Coating #1 is able to cure at temperatures as low as 35°F. It has Zero (0) VOCs. Since it has no VOCs, it has no solvent so it meets the strictest possible standard for a low VOC coating. It is often used in coolers and food preparation areas that require constant low temperatures. Product #1 Cold Temperature Cure Epoxy Coating is also frequently used in room temperature applications to meet super-fast cure, limited shutdown needs.

Product #10 Cold Temperature Curing Epoxy Mortar Resin – This product has a low modulus of elasticity (flexibility) and is Low Viscosity. The low viscosity allows heavy loading of the right fillers. The heavy filler loading helps not only to save money, but helps to maintain better thermal coefficient with respect to concrete and steel. The low modulus of elasticity prevents it from being brittle making it less vulnerable to thermal coefficient differences. It also gives it better impact resistance.

You can find more information on cold temperature cured epoxy at: http://www.epoxy.com/EpoxyColdCured.aspx.

Please send me your questions to me by email to norm@epoxy.com


Choosing the Right Epoxy Sealer

May 18, 2015

Having the knowledge of which type of sealer to use is extremely important to the overall satisfaction of the job. There are 3 basic types of epoxy sealers. The first is 100% solids epoxy, solvent based sealants and finally water based sealers. There are also urethane and acrylic sealers.

To understand how each sealant works one must understand how they act as an epoxy. http://www.epoxy.com/primersealer.aspx . The 100% solids epoxy when applied to a floor retains a consistent thickness. Epoxy.com #15 http://www.epoxy.com/15.aspx is the best product for maintaining a clear epoxy sealer without any loss of thickness due to evaporation. If you roll a gallon of material on your floor, when it hardens you maintain the thickness of the full gallon of spread coverage.

Epoxy.com #15 can be used to seal previously installed epoxy and river rock stone on pool decks or walkways. It also seals Epoxy Chip flooring, as well as acts as a binger and sealer to Epoxy quartz flooring. It provides protection, just the right amount of shine and helps to keep the water from permeating the underlying concrete. It also works well inside in garages. It is our most versatile sealer that we offer it works great on concrete inside and when properly installed outdoors.

When you apply a water based sealer or solvated sealer you will consistently loose a percentage of the thickness due to evaporation. Even though this is the case there are times when a 100% solids epoxy may not do exactly what you need it to accomplish. In this case we offer products with different components and viscosity to suit your needs as a consumer.

Epoxy.com #671  is a low viscosity, two component, carbon filled, polyamide modified conductive primer/sealer formulated with special wetting agents to provide maximum penetration into concrete surfaces. Product #671 Primer Sealer is ideal for both new and old concrete surfaces. Product #671 Conductive Epoxy Primer Sealer provides excellent resistance to wear, and can be used either alone or as a conductive sealer or as a conductive epoxy primer when used with Product #674 Electro-Static Dissipating Urethane Topcoat and our Conductive Systems.

Epoxy.com #80 is a solvented clear acrylic solution formulated to create a clear, non-yellowing protective coating. Product #80 ACRYLIC SEALER http://www.epoxy.com/acrylic-sealer.aspx provides a tough, UV and abrasion resistant film that effectively protects surfaces from moisture penetration, staining, dirt, dust, and wear. It is good for both indoor as well as outdoor applications. This works well to seal existing terrazzo floors and as well as slate.

For those in California, who don’t want to use a 100% solid material, we offer Epoxy.com http://www.epoxy.com/High-Solids-Urethane-Coating.aspx Epoxy.com # 441 is free of the health and environmental problems normally found in solvent-based urethanes, while maintaining excellent performance properties. The very low VOCs allows this urethane coating to meet the strict low VOC standards. Epoxy.com # 441 Polyurethane Coating and Sealer provides a matte finish. Product #441 water-based urethane coating and sealer has good chemical, stain, and mar resistance.

Finally the most important thing to remember when you are choosing an Epoxy.com Sealer is to make sure you are using The Right Product for The Right Job. If you would like assistance with your selection please call our Technical Support Line at 352-533-2167 and we will be happy to assist you.


%d bloggers like this: