Choosing the Right Epoxy Sealer

Having the knowledge of which type of sealer to use is extremely important to the overall satisfaction of the job. There are 3 basic types of epoxy sealers. The first is 100% solids epoxy, solvent based sealants and finally water based sealers. There are also urethane and acrylic sealers.

To understand how each sealant works one must understand how they act as an epoxy. http://www.epoxy.com/primersealer.aspx . The 100% solids epoxy when applied to a floor retains a consistent thickness. Epoxy.com #15 http://www.epoxy.com/15.aspx is the best product for maintaining a clear epoxy sealer without any loss of thickness due to evaporation. If you roll a gallon of material on your floor, when it hardens you maintain the thickness of the full gallon of spread coverage.

Epoxy.com #15 can be used to seal previously installed epoxy and river rock stone on pool decks or walkways. It also seals Epoxy Chip flooring, as well as acts as a binger and sealer to Epoxy quartz flooring. It provides protection, just the right amount of shine and helps to keep the water from permeating the underlying concrete. It also works well inside in garages. It is our most versatile sealer that we offer it works great on concrete inside and when properly installed outdoors.

When you apply a water based sealer or solvated sealer you will consistently loose a percentage of the thickness due to evaporation. Even though this is the case there are times when a 100% solids epoxy may not do exactly what you need it to accomplish. In this case we offer products with different components and viscosity to suit your needs as a consumer.

Epoxy.com #671  is a low viscosity, two component, carbon filled, polyamide modified conductive primer/sealer formulated with special wetting agents to provide maximum penetration into concrete surfaces. Product #671 Primer Sealer is ideal for both new and old concrete surfaces. Product #671 Conductive Epoxy Primer Sealer provides excellent resistance to wear, and can be used either alone or as a conductive sealer or as a conductive epoxy primer when used with Product #674 Electro-Static Dissipating Urethane Topcoat and our Conductive Systems.

Epoxy.com #80 is a solvented clear acrylic solution formulated to create a clear, non-yellowing protective coating. Product #80 ACRYLIC SEALER http://www.epoxy.com/acrylic-sealer.aspx provides a tough, UV and abrasion resistant film that effectively protects surfaces from moisture penetration, staining, dirt, dust, and wear. It is good for both indoor as well as outdoor applications. This works well to seal existing terrazzo floors and as well as slate.

For those in California, who don’t want to use a 100% solid material, we offer Epoxy.com http://www.epoxy.com/High-Solids-Urethane-Coating.aspx Epoxy.com # 441 is free of the health and environmental problems normally found in solvent-based urethanes, while maintaining excellent performance properties. The very low VOCs allows this urethane coating to meet the strict low VOC standards. Epoxy.com # 441 Polyurethane Coating and Sealer provides a matte finish. Product #441 water-based urethane coating and sealer has good chemical, stain, and mar resistance.

Finally the most important thing to remember when you are choosing an Epoxy.com Sealer is to make sure you are using The Right Product for The Right Job. If you would like assistance with your selection please call our Technical Support Line at 352-533-2167 and we will be happy to assist you.

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s

%d bloggers like this: