Installing Epoxy Novolac #633

Epoxy.com Product #633 Novolac Epoxy Coating is installed basically in 3 Steps.

  1. Properly prepare the substratemixing-Epoxy
  2. Apply 1 coat of Epoxy.com Product #899 Primer at a rate of 250 to 300 SF per gallon per coat.
  3. Apply 2 coats of Epoxy.com Product #633 at a rate of 160 to 200 SF per gallon per coat.

Product #899 Epoxy Primer and Product #633 Coating are mixed and applied the same way. These are the only differences:

  1. The spread rate
  2. The optional anti-skid is typically only added to the #633

For the sake of simplicity the procedure for mixing and installing is mentioned once below because the three coats apply virtually the same way.

Before You Start

Before you start you will want to read the following.

  • Do with Epoxies – The things that you don’t want to forget to do when using epoxy.
  • Don’ts with Epoxies – Don’t do any of these things when using epoxy.
  • Surface Preparation – Surface preparation sets the foundation for your application. If you want your job to work better and last longer be sure to read and follow these steps.
  • For a list of job supplies to install a chip flooring see www.epoxy.com/job-supplies.aspx
  • Be sure to mix both the A and the B sides of your material before starting. Be sure to use a clean stir stick or mixing paddle for both. Do not cross contaminate.

Optional Cove

Cove Base Installation – Epoxy Cove installation used to be very difficult to install. With Epoxy.com Products and this installation guide, this job is made much easier.

Primer

When installing over concrete or wood you will first want to prime with Product #899 Epoxy Primer –www.epoxy.com/899.aspx. The purpose of this primer is to go on thin (250-300 square feet per gallon) and seal the floor so you do not get air or moisture coming up into your epoxy coating which will be going on thick (160-200 square feet per gallon). The 899 epoxy primer is also thinner than the coating and so it flows out better. Over stainless steel, aluminum and galvanized metal use Epoxy.com Product #660 Aluminum Filled for the primer.

 

MIXING INSTRUCTIONS

 

Mixing is by far the most important part of installation. One method to insure accurateEpoxy_Measure_2 mix ratios is to put measurements on sticks with the appropriate mix ratio. In the case of the 899 and 633 this is 2 Parts A to 1 Part B, so you might do 3 inches “A” to 1.5 inch of “B”

It is sometimes helpful to put some duct tape on the A stick. It will help you to see your line when using the pigmented “A” side

Be sure to properly protect the floor where you will be doing your mixing.Epoxy_Measure_1

Stir the Resin “A” and the Hardener “B ”each separately in their original container before measuring and mixing the two together. Be careful to use separate stir sticks so not to cross contaminate.

Temperature of Epoxy.com Product #899 Primer and Epoxy.com Products #1, #2 and #633 must be 50 degrees F or above at time of mixing. Stir each component separately before blending. Mix two parts by volume of Part A with one part by volume of Part B for three minutes with a low speed electric drill motor equipped with a mixing paddle. Be sure the mixing paddle is large enough to mix the material completely.  You will want to use a “propeller” type mixer with blades 5 inches or bigger.

Preparing to Mix Resin and Hardener Together

  • A 5 gallon metal pail or 5 gallon plastic pail makes a great mixing110614_2044_EpoxyChipFl10.png bucket.
  • Always be sure that your mix bucket is clean and is not contaminated with anything before you mix.
  • Some people like to use the two bucket method. That allows your person mixing to be mixing while your install people are installing the last bucket.
  • If you start to show signs of your material hardening in the mix bucket, start using a new one.

Mixing Tools

  • Typically you will want to use a paddle mixer, that goes into a low speed drill.
  • Your drill mixer should be large enough to stir the entire batch at once. A mixer that only moves only the partial contents of the pail, may result in inadequate mixing. Be sure that you use a clean mixing paddle. A dirty mixing paddle can result in poor mixing or contamination of the batch.
  • When mixing try not to whip any unnecessary air into your mix, by using the slowest drill speed and keeping the mixing paddle reasonably level.

Mixing110614_2044_EpoxyChipFl7.png

  • Carefully measure out the “A” resin and the “B” hardener into two other containers.
  • Pour “A” resin into your mixing bucket and then pour the “B” hardener into the mixing bucket. Always pour the “A” first and then the “B”
  • Stir for 3 minutes, being sure to scrape the bottom and sides as you mix.mixing-Epoxy

If Anti-Skid Course or Anti-Skid Fine is to be used add 12-16 volume ounces per mixed gallon, and mix until properly dispersed, typically 1-2 minutes.

Doing the Trim

• Trim around all the areas that are difficult to roll.

• Remember not to get two far ahead, you don’t want the material to set up before it is 110614_2044_EpoxyChipFl14.pngbroadcast.

• Also remember to pull the duct tape while the material is still wet

APPLICATION

Epoxy.com Product #899 can be applied with a brush, roller or squeegee at a rate of 250-300 square feet per gallon.  Remember that if you put it on too thick you can get bubbles in the 899 Epoxy Primer. The important thing is to 110614_2044_EpoxyChipFl17.pngcompletely wet out the concrete without leaving excessive material. Allow the 899 primer to cure until hard.  Typically, 10-12 hours at 75 degrees F.  Do not allow more than 24 hours between this coat and the coat of coating to follow it. Epoxy.com 899 Primer typically requires only 1 coat.

The Epoxy.com Product #633 Novolac Epoxy Coating is typically applied at a rate of 160-200 SF per gallon per coat. Typically, 2 coats of Epoxy.com Product #633 High Chemical Resistance Epoxy are required. These coatings can be applied with the same tools as #899 Epoxy Prime.110614_2044_EpoxyChipFl20.png

When Product #633 is applied over concrete or wood, prime with Product #899 Epoxy Primer and allow the Product #899 Primer to cure to tack free. Over stainless steel, aluminum and galvanized metal use Epoxy.com Product #660 Aluminum Filled for the primer. Be sure to install the 633 within 24 hours of the installation of the primer.

For typical installations as a coating apply 2 coats of Product #633 Novolac Epoxy at a rate of 160-200 square feet per gallon per coat. This yields a wet film thickness of 8-10 mils thick per coat or 16 – 20 mils for the two coats. Since this is a 100% solids Resin and Hardener system, there is no loss during drying, so the wet film thickness and the dry film thickness for 2 coats will be identical (16-20 mils DFT). Be sure to install the second coat after the 1st coat is hard enough to walk on but before 24 hours after the installation of the previous coating.

If Anti-Skid Fine or Anti-Skid Course epoxy anti-skid additive is used add plus or minus 12 volume ounces of Anti-Skid per mixed gallon of Product #633. Never add more than 16 volume ounces per gallon of Resin and Hardener mix.

In summary:

Step 1. Good Surface Preparation

Step 2. Apply 1 coat of Epoxy.com Product #899, at a rate of 250-300 SF per gallon

Step 3. Apply 2 coats of the appropriate Product #633 Highly Chemical Resistant Novolac Epoxy Coating. Add optional anti-skid if required.

For additional help please contact Epoxy.com Technical Support at 352-533-2167 or email norm@epoxy.com.

Additional Resources:

www.epoxy.com/899.aspx

www.epoxy.com/660.aspx

www.epoxy.com/633.aspx

 

 

 

What is Most Versatile Epoxy?

Clear Chemical Resistant Epoxy #15 over Stained concrete

My company has many different products and systems. I often get asked, “What is the best epoxy?” I need details about the

Clear Chemical Resistant Epoxy #15 over Stained concrete
Clear Chemical Resistant Epoxy #15 over Stained concrete

job to answer that question. The best epoxy is the one that is right for the specific job. That is where our company’s motto “The Right Product for the Right Job” came from. This is the driving force of our company and our technical support department. This has been our driving force for 35 years.

Perhaps the real question is, “What is the most versatile epoxy?” That is an easier question to answer. It is Epoxy.com Product #15 – www.epoxy.com/15.aspx. When I was an epoxy installer I always had Product #15 Clear Chemical Resistant Epoxy Resin on my jobsite.

Advantages

  • Clear Chemical Resistant
  • Can be applied as thin as 5/1000 inch or less and as thick as 1/32 (without Filler) or more
  • Can be applied as an aggregate filled system at a thickness of 12 inches or more.
  • Excellent wetting properties
  • Good temperature resistance
  • Low Viscosity
  • Non-shrink
  • Slower than other clear epoxies to oxidize outdoor in direct sunlight
  • Strong and durable
  • Virtually non-yellowing indoors

Uses

  • Acid Stain Concrete Floor Sealer
  • Base Coving Material for seamless flooring (when mixed with fumed silica and silica sand)
  • Clear coating over most porous materials
  • Chemical resistant primer
  • Chemical resistant mortar when mixed with silica sand
  • Chemical resistant top coating
  • Clear epoxy sealer for concrete
  • Clear epoxy sealer for wood, and other porous materials
  • Counter top coating
  • Epoxy quartz flooring
  • Pothole repair in concrete (when mixed with silica sand)
  • Sealing of stone that has been previously epoxied together (aka epoxy-rock, stone carpet etc.)
  • Surface sealing concrete cracks and joints (when mixed with fumed silica thickener)
  • Use with fiberglass or Kevlar to make strong composite members
  • Waterproof wood joint sealer (when mixed with fumed silica thickener)
  • Wood bonding as neat material or mixed with fumed silica thickener
  • Wood Floor Coating

Product #15 – www.epoxy.com/15.aspx – is a great product to have around for any number of emergency situations. Please address your questions to Epoxy.com Technical Support at 352-533-2167 or email me at norm@epoxy.com.

Selecting the Right Floor for a Mechanical Room

Mechanical Room Floors are very unique in their use and conditions. You have to consider the installation environment and the function of the floor. Our Mechanical Room Floor will protect the concrete, and contain any liquids that spill.

Systems used in mechanical rooms should be zero VOC. You do not want solvent evaporating from your material. Evaporated solvent could be picked up by your air handling unit sending it through your building. The best way to prevent this is with a VOC free 100% solids resin system. A resin system that is 100% solids has no solvent (or water) in it. It also means when you spread a gallon of material on your floor after it hardens you still have a gallon of material. With water-based and solvent based materials you lose half the material to evaporation.

Mechanical rooms should be chemical resistant. Typically they are top coated with Epoxy.com Product #2 Chemical Resistant Epoxy – www.epoxy.com/2.aspx. If it is a chemical feed room you can supply a list of chemicals and concentrations to the technical support department so you can make sure the #2 is chemical resistant enough.

The systems used for mechanical rooms are impact resistant. The limiting factor is the strength of the concrete substrate. Properly installed the epoxy will stay bonded to the concrete. The only way the epoxy can chip is if you chip the concrete from underneath the epoxy. You can install a thicker epoxy floor for an additional cost if you think you need still additional protection.

The systems recommend for mechanical rooms are highly abrasion resistant and will easily handle traffic up to heavy fork lift traffic. The system can be made even thicker if you have an unusual amount of abusive traffic.

When the mechanical room is over a finished space, it is suggested that a crack isolation membrane be integrated into the system. This can be done with Product #32 Epoxy Membrane System. The advantage of #32 Epoxy Membrane Resin as part of the system is 100% solids and has zero VOCs.

If the mechanical room is shut down and you can handle solvent and want something still more flexible you can use Epoxy.com Product #459 a two component, high solids, elastomeric urethane instead of or in addition to the Product #32 Epoxy Membrane above. Product #459 exhibits excellent elongation properties along with high tensile strength and tear resistance to make it an ideal crack resistant membrane for use under Product #2 and all of our other epoxy mechanical room floor coatings.

One of the primary reasons you need a mechanical room floor over finished space below is to waterproof it. The above methods accomplish the waterproofing in the center of the floor. The edges of the floor can be protective with a coving material up the wall and around pipe penetrations. That can be accomplished with Product #720 Epoxy Coving Resin System which can be used to install an integral cove base for all of our epoxy based mechanical room flooring and most of our other epoxy flooring and coating systems. This provides seamless wall to floor protection.

For more information on seamless water and chemical resistant mechanical room flooring, contact Epoxy.com Technical Support Department at 352-533-2167, or email me at norm@epoxy.com.

 

Applying New Epoxy over Old Epoxy

I frequently get calls and emails from folks who want to install our epoxy over an existing epoxy floor or coating that they have. They want to know if it is okay to go over it and what they have to do to properly prepare the surface.

If the existing epoxy is a good hard solid one that is well bonded to a well prepared substrate it is possible. On the other hand if you are replacing it, what is wrong with the existing epoxy? Has the existing epoxy been badly abused by heavy sharp objects being dragged on it? Was the exiting epoxy damaged by chemicals beyond the chemical resistance of the existing epoxy? Are you just trying to upgrade the look of the existing epoxy?

You should be concerned about going over epoxy that is coming loose from the substrate. That may mean that there was poor surface preparation. It may also mean that the quality of the epoxy might not be what it should be. You need to be concerned about epoxy that is wearing out. If it is wearing out you want to know why. My company and I personally started out as installers of epoxy. I have never seen or been made aware of any of Epoxy.com coatings and/or flooring systems that have worn out have come loose from the concrete. I have seen concrete so pounded by traffic that it came loose, but our epoxy was still attached and still doing its job. That is based on over 30 years of field experience with the products.

Back to the question, “can I put epoxy over epoxy?” I always assume that the reason that the epoxy is wearing out or coming loose is that the epoxy is low quality or the installation was poorly done or both until I can prove otherwise. The way that I do that is to attempt to grind or shot blast off the existing epoxy. If after a substantial effort the epoxy cannot be removed and I cannot hear a hollow sound under the existing epoxy, I feel I have proven that the existing material is solid and well bonded.

Let’s take a moment to discuss that dreaded hollow sound above. If the flooring system or coating is very poorly bonded you will get a sound from your grinder like you are dragging a piece of paper or a piece of stone under the grinder, or rubbing stone. When you tap it with a hammer you get a hollow higher pitch noise than you get when you tap solid concrete or a solid floor over concrete.

You must be sure that the substrate is free of all types of contamination, including but not limited to oil, grease, food fats, curing compounds, sealers, laitance, dirt, wax etc. The existing epoxy left behind must be well bonded, and sanded until it has no shine. See Epoxy Surface Preparation Procedures for more information on this subject.

The beauty of trying to get it off is you are removing all the shine and getting it ready to accept another layer of epoxy. Just before I install the new layer of epoxy I solvent wipe with xylene, let it dry. Then I recommend a coat either Epoxy.com Product #899 Primer or Epoxy.com Product #12 Chemical Resistant Primer. Then install epoxy as usual. For more surface preparation and installation tips please visit or “Where to Start” page at: http://www.epoxy.com/start/default.aspx

Related Resources on Epoxy

“Where to Start” page may be the best way to get you off to a quick start.

Epoxy Coatings

Epoxy Primers and Sealers

Chemical Resistant Epoxy

Epoxy Chemical Resistance Chart

www.epoxy.com

Epoxy.com Technical Support
Norm Lambert, President – Technical Support Director
352-533-2167
info@epoxy.com