Basement Waterproofing with Epoxy

Many homes and businesses experience leaky basements year after year. The worse time is in the spring after winter accumulation of snow. There are a number of prudent things that you can do to improve drainage against your foundation like roof gutters, grading and improvement of drainage. The recommendations here do not replace that conventional wisdom. It is designed to augment and improve upon these conventional methods.

The following article will be 1 of 2. This one deals with Block wall foundations. The next one will deal with poured wall foundations.

Waterproofing Block Wall Foundations with Epoxy

One of the nicest features of most of our epoxies are that they are virtually 100% waterproof. Water simply cannot pass through a good healthy layer of properly applied concrete, block, wood etc. Epoxy also has an incredible bond to concrete, cement, wood and many other construction materials. The bond strength of epoxy to concrete and cement is greater than the tensile strength of the concrete. That means on properly prepared concrete, epoxy cannot be removed without pulling concrete with it. The same is true about wood.

Considerations in Waterproofing with Epoxy

All this gives you the perfect combination to make a block wall watertight. There are limitations however:

  1. In an ideal world the epoxy should be applied on the positive pressure side of the wall, the outside. This way the pressure of the water is pushing it into the wall. That helps to mitigate the likelihood that you get so much pressure on the concrete block that you fracture the block. Typically by the time you know you have a leak you are already backfilled and landscaped so 95% of the time it is not practical to do on the outside of the wall. So you do it on the inside instead.

    Water exerts a pressure of less than ½ psi per foot of water depth and most basement walls are only 8 foot high, so you would typically only see 4 psi. So it is unlikely that you have a pressure greater than the tensile strength of the block. So doing it on the inside is typically the only economical alternative.

  2. The Product #1W Epoxy is much more flexible than the concrete block and mortar, but if the mortar or concrete gets any significant cracks in it, it will crack through the coating. On the other hand, the system is very easy to patch if it does crack. We also make a wall grade version of our crack isolation membrane Epoxy.com Product #32 – www.epoxy.com/32.htm – which can reduce the potential for small cracks (which are the most common).
  3. A clean substrate is required for maximum effectiveness – www.epoxy.com/surfaceprep.aspx. For technical support contact me at norm@epoxy.com or 352-533-2167

Installation of Epoxy Waterproofing on Block Walls

Once the wall is clean, you need to point-up (fill) any cracks, bad mortar joints, and larger holes that are in the block. Some people use conventional mortar and wait 28 days for it to cure as per the American Concrete Institute. This is a very inexpensive way to do it, but can be affective if done properly. A more effective way to insure the right results is the use of Product #2005 Epoxy Gel Adhesive – www.epoxy.com/2005.aspx. That insures that you have a tight bond over the cracked areas and have already produced a tight waterproof seal in that area. Also the #2005 Gel Epoxy is semi flexible and allows more movement before cracking that conventional grout. The #2005 allows your coating to be installed the day after the #2005 is applied.

Once the cracks and holes are repaired, much of your work is done. You simply apply 1 coat of Epoxy.com Product #899 – www.epoxy.com/899.aspx – Epoxy Primer and allow to dry overnight.

After the primer has cured overnight you can apply the optional crack isolation membrane Product #32W – Wall Grade, or proceed to the coating below. If you do apply the crack isolation membrane 2 coats of the membrane are best. One advantage of the two coats of membrane is that typically you can reduce the number of coats of top coating that is required to seal the block. As you put on the membrane be sure to check to see that the holes in the block are being filled as you go.

Depending on the porosity of your concrete and if you used the crack isolation membrane above you will want to apply 2-4 coats of 1W epoxy wall coating. As you put on each coat check to see that the holes in the block wall are being filled.

Summary of Waterproofing Basement Walls with Epoxy

In conclusion: Leaking basements are a major problem to many structures in the spring. The easiest time to repair them is during the winter when there is little or no leakage. Epoxy.com epoxy coating systems can affectively and economically solve most basement leaking problems. The final product is a hard attractive ceramic like finish that does not require additional painting or other finishes over it.

Next Issue: Waterproofing Poured Wall foundations with Epoxy.

Additional Information on Epoxy Coatings

Product #1W (Wall Grade)  Epoxy Wall Coating – a general purpose epoxy wall coating

Product #2W (Wall Grade) Cemical Resistant Epoxy Wall Coating 

Product #32 (Wall Grade) Flexible Epoxy Membrane

Where to Start when installing epoxy.

Waterproof Your Life

The Concept

About 20 years I had a half way house that came to me and wanted a virtually indestructible waterproof group bathroom. They needed it to be like a shower enclosure for the entire bathroom, and toilet facility. It needed to be easy to thoroughly clean and disinfect.

The resulting system allows you to hose down the entire ceiling, wall and floors. The system that we developed is a completely seamless, waterproof ceiling and coating system. This epoxy ceiling and wall coating is seamlessly integrated with a seamless flooring system. This system is now being used for everything from clean rooms to animal facilities to car washes, daycare centers, assisted living facilities, food processing facilities and more.

The System

Ceiling and Walls

Prime the ceiling and walls with Epoxy.com Product #899 Primer – www.epoxy.com/899.aspx. Product #899 Primer is a 100% solids, low viscosity, moisture tolerant epoxy. It soaks deeply into the substrate, verifies surface preparation, and helps to prevent the much thicker coating from getting bubbles that may be cause by air or moisture trying to escape from the substrate during curing. Allow primer to get hard to the touch.

Before the epoxy primer is 24 hours old (and after the primer is hard to the touch) apply a coat of Epoxy.com Product #1W. The 1W – Wall Coating is 100% solids. It comes in a range of different colors. This means it is zero (0) VOC with no solvent. Just like the 899 Primer the 1W has very little odor. We have even more chemical resistant wall coatings for applications where it is chemicals that are being splashed or sprayed. Contact us if you have strong chemical exposures that you want to contain instead of water.

Let the first coat harden to the touch and before 24 hours add another coat of #1W. Allow the coating to dry over night.

Seamless Epoxy Cove – Optional

Typically the cove is only installed if you are going to install one of the multi-colored flooring systems (Waterproof Floor Options 2 & 3below). Cove is covered in an earlier blog – http://news.epoxy.com/2014/06/25/seamless-epoxy-cove-installation-instructions/. The cove gives you a radius at the bottom of the wall making the floor to wall transition easy to clean and esthetically pleasing.

Seamless Epoxy Flooring System

There are multiple systems that you can use for your seamless flooring portion of the system.

Water Proof Floor Option 1 – Seamless Epoxy Floor coating:

Floor Coating System – www.epoxy.com/1.htm. Product #1 applies with the Product #899 primer under it and in 2 coats just like the 1W. The Product #1 is thinner and flattens better on a floor than the Product #1W. You can also add an optional anti-skid to the #1 Floor Coating. The #1 comes in all the variety of colors of #1W.

Waterproof Floor Option 2 – Seamless Epoxy Chip Flooring:

Chip Flooring System – www.epoxy.com/chip.aspx is a two component 100% Chemical Resistant Epoxy Chip Flooring. System #315 Seamless Epoxy Multi-Colored Chip Flooring is available in virtually limitless color combinations. If your job is big enough our chips can be pigmented to match all the colors of many major paint companies. We can color match our base coat colors as well. Unless the pigments for your custom colored 315 Basecoat are unusually expensive we can color match for a modest small batch charge or at no charge for larger orders. Even our standard color pallet offers you over 45 chip colors that can be blended in any combination and percentage as you want. This gives you the architectural choices you need. The top coating for this system is highly UV resistant so since it doesn’t chalk indoors it can last and look great for decades.

Waterproof Floor Option 3: – Seamless Epoxy Quartz Flooring:

Quartz Flooring System with Product #15 – www.epoxy.com/15.aspx – is also an excellent flooring system for those who like the colored sand look with a good midrange chemical resistant system.

Waterproof Floor Option 4 – Seamless Chemical Resistant Flooring:

We can also help you to combine the systems above with our Novolac Epoxy Systems – www.epoxy.com/novolac.aspx for highly chemically resistant versions of those systems. You can also install an Electro-Static Dissipative or Conductive system www.epoxy.com/conductive.aspx.

 

In conclusion the systems above are only a small fraction of the possibilities. With our wide range of colors and chemically resistant systems the possibilities are endless. Please contact Epoxy.com Technical assistance at 352-533-2106 or email me directly at norm@epoxy.com.

Epoxy Chip Floors

Heavy traffic on floors often make the use of decorative flooring products impossible. To make this possible we created System #315 Seamless Epoxy Multi-Colored Flake Chip Floor Resurfacing System. Our #315 Chip System creates a beautiful, durable, and affordable floor that is easy to apply by both professionals and do-it-yourself enthusiasts.

Mvc-263s.jpg (41651 bytes)
A Vermont Interstate Rest Area after over 15 years

What is new and unique?

At last there is a high quality seamless floor finish which can be provided in every desirable color combination. This system is easy to use, by any skilled do-it-yourselfer or coating professional. For potential customers, both commercial applicators and the do-it-yourselfer, the final result is most certainly beautiful, affordable, and its durability insures the product to be long lasting, waterproof, easy to clean, and maintenance free.

System #315 Seamless Epoxy Multi-Colored Chip Flooring is available in virtually limitless color combinations. If your job is big enough our chips can be pigmented to match all the colors of many major paint companies. We can color match our base coat colors as well. Unless the pigments for your custom colored 315 Basecoat are unusually expensive we can color match for a modest small batch charge, or at no charge for larger orders.  Even our standard color pallet offers you over 45 chip colors that can be blended in any combination and percentage as you want.

chip Flooring picture
Water Plant after more than 15 years

By matching the base coat color in the chip, you make the system much less prone to error.  If you should happen to miss a small spot on the floor the base color shows through, looking like it is just more of that chip in that area.

System #315 chips are also available in 7 sizes ranging from a 1 inch chip down to 1/32 inch chip.  Smaller chips give the look a lot like epoxy quartz flooring. The various colors and sizes allow you to give your floor any number of looks like stone, terrazzo, colored quartz, or vibrant linoleum.

Our clear glaze coat does not yellow quickly like other epoxies.  We have some jobs that have been around for 30 years or more where no yellowing can be found, not even under the urinals in high school bathrooms. This kind of durability is perhaps the most important quality of the #315 Chip Flooring System.  Anyone can provide you with a flooring system that is attractive today.  The #315 Chip Flooring System is the flooring system you need if you want it to stay like that for years to come.

Epoxy Stone Overlays

Epoxy Stone

Installation, Repair, and Sealing of Epoxy Stone Overlays


Early Spring Special

Place your credit card order and authorize it on or before April 11, 2014 for Product #17 Epoxy Stone Adhesive or Epoxy.com Product #15 for Reglazing Stone and get it at 5% off from contractor pricing. You must mention the code “EpoxyMyStone”, to get this discount.

Epoxy Adhesive for Bonding Pebble Stone Together

Product #17 Epoxy Adhesive for Bonding Stone Overlays is a two component, 100% solids high-mod epoxy adhesive used for bonding stone and other aggregates in all types of flooring applications. Some uses of Epoxy.com Product #17 Epoxy Adhesive for Bonding Stone Overlays would include patios, pool decks, walkways and other areas where a long wearing and decorative system is desired.

Product #17 Epoxy Stone Overlays give you the beauty of a natural looking shinny stone, without the hassle of the stone needing the constant attention of loose stone. Water actually passes through the system. The #17 Epoxy Adhesive and stone give you a carpet of stone that allows the water to run down away from your feet.

Installation Product #17 Epoxy Adhesive for Bonding Stone Overlays typically uses the #17 Epoxy Stone Adhesive, and clean hard dry stone. A 3 gallon unit of Product #17 will typically mix with about 400 lbs of stone.

Glazing Pebble Stone Epoxy

Product #15 Chemical Resistant Epoxy Floor Resurfacing System  is typically used for resealing epoxy bonded stone, because it oxidizes much slower than other epoxies, and usually last much longer than other epoxies used for reglazing epoxied stone pebbles.