waterproof

Clear Epoxy Over Reclaimed Wood

by

Epoxy Product #15 on Reclaimed Wooden Floor

The floor shown in the photos was installed in a dining
room. Approximate room size was 12’ x 14’.  The lumber was 8″ – 12″ in
width and 3/4″ thick. Tongue and groove edges were routed on the boards. 6
gallons of epoxy were layered on in 7-8 applications. Epoxy was applied with
3/8″ and 1/4″ nap rollers. The final finish was not completely smooth like a
table top due to cupping in some of the boards.

The boards were bonded together because he cut heating
vents in and the cut-outs came out as one solid piece and stayed together
rather than separating back into the individual boards.

The baseboard was also made out of old lumber. The top
edge was rounded and then stained so the machined edge would appear
weathered. 3-4 coats of epoxy
were applied so it is much rougher.

The owner was definitely pleased with the results.

Photos & Job Description Courtesy of: Karl Fleming

Copyright 2012 – All Rights Reserved

See larger versions of the pictures on this page.
Rough Cut Reclaimed Barn board floor, before clear epoxy coating. Click the picture above to see a larger
Version of this picture.
Rough Cut Reclaimed Barn board floor, after clear epoxy coating. Click the picture above to see a larger
Version of this picture.

Epoxy.com Chemical Resistant Chart of Popular Products

by

Chemical Resistance Chart of Popular Epoxy.com Coating and Mortar Systems

Chemical

# 1

#2

# 630

# 633

Vinyl Ester #663
Acetone NR NR S-3 S-3 S-3
Acetic Acid – 56% 5%-S-3 10% 20% S-2 +
Acetic Acid – 84% NR NR ND S-2 S-2
Acetic Acid (Glacial) NR NR NR S-3 S-1
Aluminum Chloride – 30% NR ND + + +
Aluminum Nitrate – 50% NR ND + + +
Aluminum Sulfate – 50% NR ND + + +
Ammonium Hydroxide -30% S-3 S-2 + + S-1
Ammonium Sulfate – 50% NR S-2 + + +
Ammonium Sulfide -50% NR S-2 + + +
Barium Sulfate NR S-1 + + +
Barium Sulfide NR S-1 + + +
Beer S-2 + + + +
Benzene NR NR S-2 S-2 S-2
Benzyl Alcohol NR S-2 + + S-2
Black Liquor NR ND + + +
Butyl Acetate NR S-3 + + +
Butyl Acetate (Normal) NR ND ND + +
Brake Fluid ND + + + +
Butanol (Normal) NR S-3 + + +
Calcium Chloride NR S-2 + + +
Calcium Hydroxide ND S-2 + + +
Carbon Tetrachloride NR S-3 ND + +
Citric Acid -40% S-3 S-1 S-1 S-1 +
Corn Oil ND + + + +
Crude Oil – Sour NR + + + +
Crude Oil -Sweet NR + + + +
Cumene NR S-3 ND + +
Cutting Oil NR S-1 + + +
Cyclohexeone NR S-3 S-3 + +
Diacetone Alcohol NR S-2 S-2 + +
Diesel Fuel + + + + +
Diethylene Glycol ND + + + +
Distilled Water ND + + + +
Ethanol NR S-2 + + S-1
Ethyl Acetate NR S-2 + + S-2
Ethyl Alcohol NR S-2 + + S-2
Ethylene Dichloide NR NR S-1 S-1 ND
Ethylene Glycol ND + + + +
Ethyl 3-Ethoxypropionate ND ND ND + ND
Ethylene Oxide NR ND ND + +
Ethlene Glycol Monopropyl Ether NR ND ND + ND
Freon ND ND S-1 S-1 ND
Fuel Oil ND + + + +
Gasoline (Unleaded) ND S-2 + + +
Gasoline (Premium Unleaded) ND S-2 + + +
Glucose NR S-1 + + +
Glycerine NR + + + +
Glyoxal – 40% NR ND + + S-2
Heptane NR S-2 + + +
Hexane NR S-2 + + +
Hexalene Glycol S-3 S-1 + + +
Hydraulic Fluid ND S-1 + + +
Hydrochloric Acid -10% S-2 S-1 + + +
Hydrochloric Acid 36% NR S-2 + + +
Hydrogen Peroxide -5% S-3 S-1 + + +
Hydrogen Peroxide – 30% NR S-2 ND + +
Iodine NR S-3 (Stain) + + +
Isobutyl Alcohol NR S-2 + + +
Isopropyl Alcohol NR S-2 + + +
JP – 4 Jet Fuel S-2 S-1 + + +
JP – 5 Jet Fuel S-2 S-2 + + +
Kerosene NR S-2 + + +
Ketchup S-3 + + + +
Lactic Acid – 50% NR S-2 + + +
MAK NR ND ND + ND
MEK NR NR S-3 S-3 S-3
Methanol NR ND + + S-2
Methylene Chloride NR NR NR NR NR
MIBK NR NR S-2 + S-2
Mineral Spirits NR S-3 + + +
MTBE NR NR + + ND
Naptha (VMP) NR S-3 + + +
Nitric Acid – 10% NR S-1 + + +
Nitric Acid – 30% NR NR NR NR +
Oxalic Acid NR ND + + +
Para Xylene NR ND ND + ND
Peanut Oil NR S-3 + + +
Perchloroethylene NR NR + + +
Phosphoric Acid – 10% S-3 + + + +
Phosphoric Acid -75% NR S-3 + + +
Phosphoric Acid – 85% NR S-3 + + +
Power Staring Fluid ND S-2 + + +
Propylene Glycol Monomethyl Ether NR ND ND + ND
Propylene Glycol Monomethyl Ether Acetate NR ND ND + ND
Pseudocumene NR ND ND + ND
Skydrol 500B S-2 + + + +
Sodium Hydroxide -50% + + + + +
Sodium Hydroxide – 70% NR S-2 + + S-2
Sodium Hypochlorite – 10% ND + + + +
Sodium Nitrate – 50% NR S-2 + + +
Sulfamic Acid ND S-1 + + +
Sulfuric Acid – 10% + + + + +
Sodium Bisulfiate ND ND ND S2 ND
Sulfuric Acid 50% S-3 S-2 + + +
Sulfuric Acid 70% NR NR + + +
Sulfuric Acid 98% NR NR S-1 + S-2
Toluene NR S-3 + + +
Tomato Juice NR S-2 + + +
Transmission Fluid NR S-2 + + +
1.1.1 Trichloroethane NR NR ND + +
Urine NR + + + +
Vinegar NR NR + + +
Vinyl Tolene ND ND + + +
White Liquor ND ND + + +
Xylene NR S-1 + + +
+ = Continuous Service (greater than 6 months)

S1 = Splash and Spill with Weekly Cleanup

S2 = Splash and Spill with 24 hour Cleanup

S3 = Splash and Spill with Hourly Cleanup

NR= Not Recommended

ND= No Data

Factors such as temperature, application,
Exposure, Etc. are beyond the control of
Epoxy.com a division of  Epoxy
Systems, Inc. No warranty concerning these studies can be made.  Samples should be tested under actual
or simulated condition for final decision on the suitability of the system.
April 14, 2011

Epoxy Coating and Flooring Installation Job Supplies

by

Here is a suggested list of the materials that you will need for most typical epoxy coating systems.  This list is also useful for installing roller applied coating systems like Epoxy.com Chip Flooring.

  • 1 roller pan
  • 6 inserts for roller pan
  • 15 stir sticks
  • 12 (5 QT) plastic pails
  • 3 (5 G) plastic pails
  • Roll of Duct Tape
  • 5 heavy duty 9″ roller frames
  • 6 (3/8″ nap) roller covers *be sure the roller nap doesnot fall apart in hands*
  • Roller handle extension poll
  • 4 Hard Plastic Body Filler type Squeegees
  • Paper 6oz Dixie cups
  • 2 (2 blade) mixing paddles – should be at least 5 inches in diameter and capable of being used in a heavy duty drill
  • Heavy Duty Drill for mixing paddles above
  • 6 (2″) paint brushes  *check bristles to be certain they CAN NOT be pulled out*
  • Latex (or non latex) rubber gloves
  • Vacuum (Shop Vacuum Quality)
  • Stiff Bristled Broom *check to make sure bristles do not fall out*
  • Chalk line or laser to set lines that need to be masked
  • Roll of plastic to keep buckets on to avoid drips onto floor
  • Go Jo Hand cleaner or fast orange for hands and skin

*Note – Epoxy does NOT come out of fabrics*

For more information visit www.epoxy.com.

Why Use Epoxy.com Products in “Green” Buildings?

by

110614_2044_EpoxyChipFl10.pngEpoxy.com’s 100% solid products (which are most of our product line) are included in many “Green” buildings. The logic for that is this:

1. Epoxy.com 100% solid products have  no VOCs. So you are reducing the carbon emissions.

2. Typical Epoxy.com 100% solid systems have done their job for decades, and there is no reason to believe they will not last for decades more. I personally have jobs that I installed with them that go back as much as a third of a century, that are not even starting to show signs that they will need replacement. That is the ultimate in reuse.

3. There is no need to recycle a product that can be reused for decades, but you can use recycled materials like glass aggregate in the epoxy matrix.

Epoxy.com encourages our customers to order material as they need it and to use all their materials before their expiration. That is why we do not require large stocking orders from new dealers, like most other companies. We want our customers to use up material they buy from us and not have any for it run out of shelf life. However, if Epoxy.com products do run out of shelf life, they are typically mixed and cured before disposal as is consitered in under most if not all local regulations as inert as common trash.

You can find more information about Epoxy.com Zero (0) VOC products at: https://www.epoxy.com/zero_voc.aspx

www.epoxy.com – Epoxy.com Home Page.

Please like our Facebook page at: www.facebook.com/epoxy.com/