Methyl Methacrylate (MMA) Primer

October 6, 2010

Epoxy.com Product #691

Methyl Methacrylate (MMA) Flooring Primer


DESCRIPTION

Epoxy.com Product #691 Methyl Methacrylate (MMA) Flooring Primer is a 100%
reactive Methyl Methacrylate primer for all
Epoxy.com MMA floor and wall
systems
. Epoxy.com Product #691 Methyl Methacrylate (MMA) Flooring Primer also
provides excellent filling and sealing as a scratch work filler (with filler
added) to level uneven floor and wall surfaces. Epoxy.com Product #691 Methyl
Methacrylate (MMA) Flooring Prime
r is a reactive Methyl Methacrylate resin, which
hardens rapidly with the addition of Epoxy.com Product #695 MMA hardener, even
at low temperatures.

ADVANTAGES

  • Fast cure (60 min.) for rapid recoat.
  • Good wetting properties for excellent bond to concrete.
  • VOC compliant (100% solids).
  • Full strength in less than 1 hour.
  • Use over wide temperature range – even below freezing.

CONSIDERATION

  • Substrate must be dry and free of dirt, waxes, curing agents and other foreign materials.
  • Should not be installed on fresh concrete until maximum shrinkage has occurred (at least 30 days after placement).
  • On or below grade installation must have an efficient vapor barrier under the slab (minimum 10-15 mil).
  • Moisture Vapor Transmission must be less than 3 lbs per ASTM-F-1869 and less than 80% RH perASTM F-2170.

COMPOSITION

Epoxy.com Product #691 Methyl Methacrylate (MMA) Flooring Primer is a 100% reactive
Methyl Methacrylate resin.

COLOR SELECTION

Epoxy.com Product #691 Methyl Methacrylate (MMA) Flooring Primer is supplied clear. Color packs are available for selected colors. Color pack
mix ratio is 1 quart pigment per 5 gallons resin. See Epoxy.com MMA Color Card.

SURFACE PREPARATION

Surface preparation is the most critical portion of any successful resinous
flooring system. All substrates must be properly prepared as outlined in
Epoxy.com Surface Preparation Guide.

MIXING AND INSTALLATION

Epoxy.com Product #691 Methyl Methacrylate (MMA) Flooring Primer requires the addition of Epoxy.com Product #695 Hardener to start the hardening
process. The amount of hardener must be adjusted to the respective surface temperature (see table below). At temperatures below 40°F, Accelerator 101 must be used in addition to the amount of hardener
used at the 40°F level (about ° oz by vol./gal. @ 32°F up to 2.0 oz by vol./gal. @ -20°F).

Epoxy.com Product #691
MMA Primer 
SUBSTRATE/MATERIAL TEMPERATURE (°F) Epoxy.com Product #695 MMA Hardener (BPO)VOL OZ.PER GALLON OF RESIN
30°F 12.7
40°F 9.0
50°F 7.5
60°F 5.5
70°F 3.5
90°F 1.8

See Epoxy.com Product #695 MMA Hardener
Tech Data Sheet for more details and catalyzing Epoxy.com
Product #691.

Spread
Epoxy.com Product #691 Methyl Methacrylate (MMA) Flooring Primer 
evenly on the surface (no puddles) with notched trowels, and/or squeegees
and back rolled with short nap mohair rollers at no less than 100 sq ft/gal. on very
absorbent surfaces. Two coats may be necessary to get an even, resin-rich surface to bond with the next layer.

It is recommended to broadcast 16-30 mesh quartz sand (approximately 4 lbs/100 sq ft) into the wet primer. This
will help in the application of the coating or troweled mortar. Apply next application only after the primer is
completely hardened.

PHYSICAL PROPERTIES

Percent Reactive 100% (Zero VOC)
Working Life 10-15 min.
Recoat Time Approx. 60 min.
Viscosity 250-270 cps
Weight per Gallon 8.3 lbs

CLEAN UP

Clean tools and equipment with lacquer thinner or MEK. Consult Material
Safety Data Sheet for safety and health precautions.

COVERAGE

100 square feet per gallon, minimum thickness.

STORAGE

Store in a cool and dry place, below 80°F, out of direct sunlight. Do not
store near open flame or food. Shelf life is 4 months in the original unopened containers.

HELPFUL HINTS

Adequate cross ventilation should be provided. Good ventilation during the
processing ensures a good cross linking and hardening. Read, understand and follow Material Safety Data
Sheets and Application Instructions prior to use. Use only as directed. If substrate and/or material temperature is above
90°F, DO NOT apply material.

For industrial Use only.

Keep out of reach of children.

Contact Epoxy.com Technical Support with your questions about this
product at 352-533-2167. Epoxy.com Technical Support Department can help you
with the selection, specification, installation, and maintenance of
Epoxy.com products, or visit http://www.epoxysystems.com.

Norm Lambert
President &
Director of Technical Support
Epoxy Systems, Inc
Available by Phone M-F 9AM-4PM Eastern Time (6 AM – 1 PM Pacific Time)
352-533-2167 (Voice)
352-465-3497 (fax)
norm@epoxy.com

 [Home]
[Catalog of Products]
[Where to Start]
[Bonding Systems]
[Chip Floors]
[Chemical Resistance]
[Coatings]
[Conductive]
[Applications]
[Elastomeric Polyurethane Systems]
[Garage
Floors
] [High Temperature]
[Industrial Floors]
[Injection]
[Joint Systems & Sealants]
[Mortars / Grouts]
[Novolac]
[Polymer Systems]
[Primers Sealers]
[Misc.] [Seamless Flooring]
[Waterproofing]
[Dealers Wanted]
[Installation Tips]
[Product Guide]
[Wood Filler]
[Who We Are]
[Guide Specs]
[Tech Data Sheets in Acrobat Format]
[MSDS in Acrobat Format]


New Epoxy.com Electro Static Dissipative Epoxy

September 1, 2010

Epoxy.com announces a new ESD Epoxy Product

New Epoxy Electrostic Dissipative (ESD) Epoxy Coating

Less Expensive, Easier to Use, More Durable


Epoxy.com Product #677

Electro Static Dissipative (ESD) /CONDUCTIVE COATING


DESCRIPTION

Epoxy.com Product #677 is a pigmented, water-based epoxy coating designed to achieve either an electro-static dissipative (ESD) finish or conductive finish by
modifying the underlying system components and thickness. Epoxy.com Product #677 has very low odor making it suitable for use in occupied
buildings and has high bond strength and adhesion to concrete and other surfaces.

ADVANTAGES

  • Durable, Attractive, Chemical Resistant, Non-Porous, Light Reflective Finish.
  • Low Odor during application and cure.
  • Maintains Electrical Conductivity Performance over the Wear Life of the System
  • Fast Dry and Re-coat Time.
  • Easy Clean-up.
  • Provides an ESD finish in the range of 1,000,000 to 1,000,000,000 ohms resistance when used over a non-conductive
    primer/basecoat or a conductive finish in the range of 25,000 to 1,000,000 ohms resistance when used over a conductive primer/basecoat.

CONSIDERATIONS

  • Substrate must be above 50°F and relative humidity below 85% for proper curing.
  • Substrate must be free of dirt, waxes, curing agents and other foreign materials.
  • Excessive moisture in the substrate will require a moisture vapor control treatment.

TYPICAL USES

Concrete floors and walls in electronic component assembly areas, data processing, military/aerospace, pharmaceutical plants,
hazardous industries (dust or explosion hazards). For use in any areas where the build-up of static electricity is a concern or a spark-proof floor is required.

APPLICATION

SURFACE PREPARATION

Surface Preparation is the most critical portion of any successful resinous flooring system application. All
substrates must be properly prepared and tested for moisture as outlined in Epoxy.com
Surface Preparation Guidelines.

INSTALLATION

Mix Part B of Epoxy.com Product #677 prior to combining. Mix 1 part Part A with 2 parts Part B. Epoxy.com Product #677 at a rate of 200 ft2
per gallon per coat with a short nap roller. Care should be taken to avoid
puddles. Two coats are necessary to insure uniform coverage.

Epoxy.com Product #677 Thin-Film ESD Epoxy Coating System 12-15 Mils(1,000,000-1,000,000,000 ohms)

Material Qty./ 1000 SF Coverage
1. Epoxy.com Product #899 Epoxy Primer 4-5 gallons 200-250 SF /gallon
2. Epoxy.com Product #677 ESD/Conductive Epoxy Coating 5 gallons 200 SF /gallon
3. Epoxy.com Product #677 ESD/Conductive Epoxy Coating 5 gallons 200 SF /gallon

CLEAN-UP

Clean skin with soap and water. Tools and equipment should be cleaned with warm soapy water, xylene or lacquer thinner. Consult Material Safety Data for safety and health precautions.

COMPOSITION

Waterborne Epoxy Resin and Conductive Fillers

COVERAGE

Epoxy.com Product #677, when applied at 200 SF per gallon, yields 5.2 �to 6.0 mils dry film thickness.

TECHNICAL DATA

Viscosity @ 75°F 600-1000 CPS
Mixing Ratio 1 Part A to 2 Parts B by Volume
Solids Content, by volume 50-55%
Volatile Organic Content (VOC) <20 gm/L
Bond Strength to Concrete 400-500 psi (100% concretefailure
Weight per Gallon, mixed 8.75-9.00 pounds per gallon, mixed

CURE/DRY TIME

Pot Life 20-30 min.
Dry to touch 6 hours @ 75°F
Recoat 8-24 hours @ 75°F
Light Traffic 24 hours @ 75°F
�H� Hardness 2 days
�5-H� Hardness 30 days

AVAILABILITY

Contact Epoxy.com Customer Service Department at 321-206-1833

Maintenance

Remove animal fats, oil, grease or soap film promptly to reduce slipperiness. Epoxy.com Product #677 can be cleaned with neutral soaps and detergents.
If long periods of heavy traffic cause wear patterns reapply as need.
Anti-skid materials will reduce the effectiveness of the static dissipative
properties of this material.  Do not use aggressive anti-skids. It is
impossible to get an accurate reading of the conductivity of the floor if
anti-skids are used.

Technical Services

Contact Epoxy.com Technical Support with your questions about this
product at 352-533-2167. Epoxy.com Technical Support Department can help you
with the selection, specification, installation, and maintenance of
Epoxy.com products, or visit http://www.epoxysystems.com.

Norm Lambert
President &
Director of Technical Support
Epoxy Systems, Inc
Available by Phone M-F 9AM-4PM Eastern Time (6 AM – 1 PM Pacific Time)
352-533-2167 (Voice)
352-465-3497 (fax)
norm@epoxy.com

 [Home]
[Catalog of Products]
[Where to Start]
[Bonding Systems]
[Chip Floors]
[Chemical Resistance]
[Coatings]
[Conductive]
[Applications]
[Elastomeric Polyurethane Systems]
[Garage
Floors
] [High Temperature]
[Industrial Floors]
[Injection]
[Joint Systems & Sealants]
[Mortars / Grouts]
[Novolac]
[Polymer Systems]
[Primers Sealers]
[Misc.] [Seamless Flooring]
[Waterproofing]
[Dealers Wanted]
[Installation Tips]
[Product Guide]
[Wood Filler]
[Who We Are]
[Guide Specs]
[Tech Data Sheets in Acrobat Format]
[MSDS in Acrobat Format]


Epoxy.com Seamless Epoxy Garage Flooring

August 23, 2010

Epoxy Garage Flooring Systems

Highest Quality Most Durable Garage Flooring Systems

Seamless Flooring and Seamless Epoxy Coatings – At Highly Affordable Prices


Epoxy.com offers a wide variety of Epoxy Garage Flooring products. We combine these products with related technologies, to
provide a wide variety of solutions to your Epoxy Garage Flooring needs.

Every Epoxy Garage Floor job is slightly different. The needs of each individual owner of the soon to be installed Epoxy Garage Floor has specific needs. The minimum requirement for all Epoxy Garage Floor Systems that Epoxy.com offers is that, when properly installed, are highly durable.
Selection of product needs will also need to balance the following needs:

  • Your surface preparation requirements and conditions
  • Your Aesthetic Requirements
  • Your Budget Requirements.

Sealers

MAJOR USES

  • Parking garage decks, and ramps
  • Shop and warehouse floors
  • Floors where food processing occurs
  • Columns and beams
  • Residential Epoxy Garage Floors
  • Whenever new or old concrete must be protected from the effects of chloride ion penetration, free water, water-born contaminants, freezing and thawing, petroleum products, and abrasion.

Epoxy Garage Floor Sealing Systems give you the most “bang for the buck”. They are low cost, easy to use and very durable. Epoxy.com offers this system in two formats:Epoxy.com Product #223 Water Based Curing Compound, Sealer and Bonding Agent is a two component water based epoxy curing that is used to both cure and seal concrete and to bond freshly placed concrete to existing concrete.

ADVANTAGES

  • Water based – Low V.O.C.
  • Excellent Adhesion to Damp Concrete
  • Prevents Intrusion of water, salts and chlorides
  • Easy to use 1 to 1 mix ratio
  • Can be brushed, rolled or sprayed
  • Long Pot life
  • No Reduction Needed For Spraying
  • Easy Water Cleanup

Epoxy.com Product #870 Epoxy Sealer is a two-component penetrating epoxy sealer (with very high solids) designed for superior protection of new concrete or for prolonging the serviceability of partially-deteriorated concrete. The sealer is a low to medium viscosity material and is capable of providing an effective membrane barrier to inhibit moisture migration and corrosive chemical penetration. In the cured state Epoxy.com Product #870 allows moisture vapor transmission; it seals off moisture entry but still allows the concrete to breath. When applied to concrete placed and finished in accordance with standards defined in ACI 201 (Guide to Durable Concrete), Product #870 realy improves wear resistance of the concrete surface, slows down the corrosion of reinforcing steel and adds many years’ life to the structure. Poduct #870 has a solids content of 50% after curing. It may be applied to dry surfaces at temperatures of 40°F (0°C) or above.

ADVANTAGES

  • High Solid Content – makes the product very cost effective
  • Prevents Intrusion of water, salts and chlorides
  • Easy to use 1 to 1 mix ratio
  • Can be brushed, rolled or sprayed
  • Quick Setting
  • Can be Reduced if required

Solid Colored Epoxy Garage Floor Coatings

Epoxy.com Solid Colored Epoxy Garage Floor Coating Systems are perhaps the most versatile of all Epoxy Garage Floor Systems. Properly installed they are not effected by hot tires. Properly installed Epoxy.com Solid Colored Epoxy Garage Floor Coating Systems will last for generations. It may very well be the last Epoxy Garage Floor Coating that you will ever have to install.

  • Solid Colored Epoxy Garage Floor Coating Systems can be installed as a smooth ceramic like finished Epoxy Garage Floor.
  • Colored Epoxy Garage Floor Coating Systems can be installed with the addition of an anti-skid which is available in both fine and course.
  • The 100% Solids Colored Epoxy Garage Floor Coating Systems can be installed as a single broadcast system.
    This will create a Colored Epoxy Garage Floor Coating Systems that is about 1/16 inch thick.
  • The 100% Solids Colored Epoxy Garage Floor Coating Systems can be installed as a double or even triple broadcast system. Each broadcast adds about 1/16 inch to the total thickness.

Epoxy.com has hundreds of products. So there are too many possible Colored Epoxy Garage Floor Coating Systems
to list them all here. The products that are most commonly used to create Colored Epoxy Garage Floor Coating Systems are:

  • Product #1 AllPurpose Coating – a 100% solids epoxy Hi-Build epoxy coating used for high foot and light to moderate forklift and indoor vehicular traffic areas where abrasion resistance is required; for protection against mild corrosion; and as a decorative waterproof coating for Epoxy Garage Floors, steel and concrete tanks, etc Available in normal, fast, and Cold Temperature Cure versions. Can be used for all 4 types of Solid Colored Epoxy Floor Coating Systems listed above. This product is available in 15 standard colors plus black and white, for a total of 17 standard colors. Zero(0) VOC Epoxy.
  • Product #2 Chemical Resistant Coating – a two component, 100% solids epoxy chemical resistant coating used to protect chemical
    concrete, steel and other structural materials from non-oxidizing acids and alkalines for both interior and exterior applications. Available in normal, fast, and Cold Temperature Cure. Can be used for all 4 types of Solid Colored Epoxy Floor Coating Systems listed above. This product is available in 15 standard colors plus black and white, for a total of 17 standard colors. Zero (0) VOC Epoxy.
  • Product #222 Water Based Epoxy – Epoxy.com Product #222 WATER BASED EPOXY COATING is a two component 100% reactive water based multifunctional epoxy resin coating. Product #222 is manufactured to produce the utmost in performance in a safe, water borne coating. Product #222 provides excellent resistance to salt intrusion, and excellent adhesion to most common construction substrates. Stock color for this product is gray. It is available in white, black and other shades of gray with a large enough order and enough lead time. Best if used for high build coating systems. Not as nearly as good for broadcast systems as Epoxy.com Product #1, Product #2, or Product #315NH. Water cleanup, makes this the easiest of all Epoxy.com Solid Colored Epoxy Garage Floor Systems.
  • Epoxy.com #315NH is a 100%solids, moisture-insensitive epoxy coating. EPOXY.COM #315NH mixed at 2 :1 by volume ratio, produces an excellent coating for dry or damp concrete, wood, or steel surfaces. Epoxy.com #315NH is available in a summer grade and winter grade formulation. It can be used as a stand alone coating or as a base coat for Epoxy.com chip floor. The only stock color for Epoxy.com Product #315NH is gray. No part of the Product #315NH is considered a hazmat for shipping purposes, so it can be shipped by most standard shipping methods, and to most countries. It is available in white, black and other shades of gray with a large enough order and enough lead time. Can be used for all 4 types of Solid Colored Epoxy Floor Coating Systems listed above. Zero
    (0) VOC Epoxy. Not a Hazmat to ship.

Epoxy Garage Chip Flooring Systems

Arguably the most cost effective, durable, and attractive Epoxy Garage
Flooring System available to day is Epoxy.com Chip
Flooring System
. Multi-Colored Epoxy Garage Floors have a special role to
play in interior design. The heavy technical demands made on floors often make
the use of certain decorative products simply impossible. The use of color
chips can change all that! Color chips are increasingly being used in
combination with “wet” products such as Epoxy.com Product #315 Polymeric
Multi-Colored Chip Floor Resurfacing System
to create decorative floors
with more to offer than other ornamental products…Quality! Due to their easy
application, these products can be used by both professionals and skilled
do-it-yourself enthusiasts.

Note: This product is not available in retail (off the shelf)
outlets. It is only available from select authorized applicator/distributors
or directly from
Epoxy.com, who will give you the technical support that
you need to install it properly. Get the
REAL THING.
Be sure it has the Epoxy.com logo on the label.

Epoxy Garage Flooring – Quartz

Epoxy.com Epoxy Garage Flooring with Quartz –
www.epoxy.com/15.htm, is a highly durable and
economical Epoxy Garage Flooring System that is rugged enough for even the
most demanding commercial applications of Epoxy Garage Flooring.

The backbone of the Epoxy.com Epoxy Garage Flooring
system with Quartz is Epoxy.com Product #15. Product #15 has been used
in demanding applications for over 30 years. It can be found in high
school bathrooms where it was installed in the late 70’s. The very
floors that were installed in the 70’s have shown virtually no wear and no
yellowing. You cannot do say that about typical Epoxy Quartz Flooring
Systems.

Summary

Epoxy.com believes in the Right Product for the Right Job. You do not have to accept a cookie cutter solution
to your Epoxy Garage Floor. We offer many options. Above we are just a few possible solutions. Please call Epoxy.com
Technical Support at 352-533-2167 and let us help you design the right system for your Epoxy Garage Floor.

[Epoxy.com Home Page]
[Catalog of Products]
[Where to Start]
[Bonding Systems]
[Chip Floors]
[Chemical Resistance]
[Coatings]
[Conductive]
[Applications]
[Elastomeric Polyurethane Systems]
[Garage
Floors
] [High Temperature]
[Industrial Floors]
[Injection]
[Joint Systems & Sealants]
[Mortars / Grouts]
[Novolac]
[Polymer Systems]
[Primers Sealers]
[Misc.] [Seamless Flooring]
[Waterproofing]
[Dealers Wanted]
[Installation Tips]
[Product Guide]
[Wood Filler]
[Who We Are]
[Guide Specs]
[Tech Data Sheets in Acrobat Format]
[MSDS in Acrobat Format]
[Online Ordering Authorization Form]


Epoxy.com Splash Zone and Under Water Coating and Paste

August 19, 2010


Below are some of the questions that have been emailed to Norm Lambert at norm@epoxy.com and some of his answers.
Have a question for Epoxy.com?  If so, please email Epoxy.com Technical Support.

Patching and Coating With Epoxy.com Products at and Below the Water Line

Q: I am looking for a material that I can use to patch and coat a concrete seawall.  I need to repair areas where the salt damage has eaten away
the concrete, and protect the rest of the surfaces. The area I need to do is in the tidal zone.  I can clean up the concrete, dry it up (if I
need to) and apply the a material  during low tide, but the product will need to be either very fast setting or be able to cure under water when
the tide comes in.  What do you recommend?

Norm Lambert: First you will want to do good surface prepartion – www.epoxy.com/surfaceprep.aspx. Then you will want to use Epoxy.com Product #707 Splash Zone Coating and Underwater Paste is a moisture-insensitive, two-component, 100% solids epoxy-resin system. When mixed at a 1:1 ratio, by volume, this product produces a paste-like material that is ideal for protection or restoration of concrete, steel and timber piles and other structural elements in marine environments. It will easily do what you are looking to do and a whole lot more as well.

 Epoxy.com Product #707 Splash Zone Coating and Underwater Paste has a long pot-life, and is available in a
fast Cure.  Epoxy.com Product #707 Splash Zone Coating and Underwater Paste can be hand applied, above, at or below the water line. 
It resists wave action and will even bond to wet surfaces.

Norm Lambert
President &
Director of Technical Support
Epoxy Systems, Inc
Available by Phone M-F 9AM-4PM Eastern Time (6 AM – 1 PM Pacific Time)
352-533-2167 (Voice)
352-465-3497 (fax)
norm@epoxy.com

 [Epoxy.com Home Page]
[Catalog of Products]
[Where to Start]
[Bonding Systems]
[Chip Floors]
[Chemical Resistance]
[Coatings]
[Conductive]
[Applications]
[Elastomeric Polyurethane Systems]
[Garage
Floors
] [High Temperature]
[Industrial Floors]
[Injection]
[Joint Systems & Sealants]
[Mortars / Grouts]
[Novolac]
[Polymer Systems]
[Primers Sealers]
[Misc.] [Seamless Flooring]
[Waterproofing]
[Dealers Wanted]
[Installation Tips]
[Product Guide]
[Wood Filler]
[Who We Are]
[Guide Specs]
[Tech Data Sheets in Acrobat Format]
[MSDS in Acrobat Format]
[Online Ordering Authorization Form]