New Epoxy.com Electro Static Dissipative Epoxy

Epoxy.com announces a new ESD Epoxy Product

New Epoxy Electrostic Dissipative (ESD) Epoxy Coating

Less Expensive, Easier to Use, More Durable


Epoxy.com Product #677

Electro Static Dissipative (ESD) /CONDUCTIVE COATING


DESCRIPTION

Epoxy.com Product #677 is a pigmented, water-based epoxy coating designed to achieve either an electro-static dissipative (ESD) finish or conductive finish by
modifying the underlying system components and thickness. Epoxy.com Product #677 has very low odor making it suitable for use in occupied
buildings and has high bond strength and adhesion to concrete and other surfaces.

ADVANTAGES

  • Durable, Attractive, Chemical Resistant, Non-Porous, Light Reflective Finish.
  • Low Odor during application and cure.
  • Maintains Electrical Conductivity Performance over the Wear Life of the System
  • Fast Dry and Re-coat Time.
  • Easy Clean-up.
  • Provides an ESD finish in the range of 1,000,000 to 1,000,000,000 ohms resistance when used over a non-conductive
    primer/basecoat or a conductive finish in the range of 25,000 to 1,000,000 ohms resistance when used over a conductive primer/basecoat.

CONSIDERATIONS

  • Substrate must be above 50°F and relative humidity below 85% for proper curing.
  • Substrate must be free of dirt, waxes, curing agents and other foreign materials.
  • Excessive moisture in the substrate will require a moisture vapor control treatment.

TYPICAL USES

Concrete floors and walls in electronic component assembly areas, data processing, military/aerospace, pharmaceutical plants,
hazardous industries (dust or explosion hazards). For use in any areas where the build-up of static electricity is a concern or a spark-proof floor is required.

APPLICATION

SURFACE PREPARATION

Surface Preparation is the most critical portion of any successful resinous flooring system application. All
substrates must be properly prepared and tested for moisture as outlined in Epoxy.com
Surface Preparation Guidelines.

INSTALLATION

Mix Part B of Epoxy.com Product #677 prior to combining. Mix 1 part Part A with 2 parts Part B. Epoxy.com Product #677 at a rate of 200 ft2
per gallon per coat with a short nap roller. Care should be taken to avoid
puddles. Two coats are necessary to insure uniform coverage.

Epoxy.com Product #677 Thin-Film ESD Epoxy Coating System 12-15 Mils(1,000,000-1,000,000,000 ohms)

Material Qty./ 1000 SF Coverage
1. Epoxy.com Product #899 Epoxy Primer 4-5 gallons 200-250 SF /gallon
2. Epoxy.com Product #677 ESD/Conductive Epoxy Coating 5 gallons 200 SF /gallon
3. Epoxy.com Product #677 ESD/Conductive Epoxy Coating 5 gallons 200 SF /gallon

CLEAN-UP

Clean skin with soap and water. Tools and equipment should be cleaned with warm soapy water, xylene or lacquer thinner. Consult Material Safety Data for safety and health precautions.

COMPOSITION

Waterborne Epoxy Resin and Conductive Fillers

COVERAGE

Epoxy.com Product #677, when applied at 200 SF per gallon, yields 5.2 �to 6.0 mils dry film thickness.

TECHNICAL DATA

Viscosity @ 75°F 600-1000 CPS
Mixing Ratio 1 Part A to 2 Parts B by Volume
Solids Content, by volume 50-55%
Volatile Organic Content (VOC) <20 gm/L
Bond Strength to Concrete 400-500 psi (100% concretefailure
Weight per Gallon, mixed 8.75-9.00 pounds per gallon, mixed

CURE/DRY TIME

Pot Life 20-30 min.
Dry to touch 6 hours @ 75°F
Recoat 8-24 hours @ 75°F
Light Traffic 24 hours @ 75°F
�H� Hardness 2 days
�5-H� Hardness 30 days

AVAILABILITY

Contact Epoxy.com Customer Service Department at 321-206-1833

Maintenance

Remove animal fats, oil, grease or soap film promptly to reduce slipperiness. Epoxy.com Product #677 can be cleaned with neutral soaps and detergents.
If long periods of heavy traffic cause wear patterns reapply as need.
Anti-skid materials will reduce the effectiveness of the static dissipative
properties of this material.  Do not use aggressive anti-skids. It is
impossible to get an accurate reading of the conductivity of the floor if
anti-skids are used.

Technical Services

Contact Epoxy.com Technical Support with your questions about this
product at 352-533-2167. Epoxy.com Technical Support Department can help you
with the selection, specification, installation, and maintenance of
Epoxy.com products, or visit http://www.epoxysystems.com.

Norm Lambert
President &
Director of Technical Support
Epoxy Systems, Inc
Available by Phone M-F 9AM-4PM Eastern Time (6 AM – 1 PM Pacific Time)
352-533-2167 (Voice)
352-465-3497 (fax)
norm@epoxy.com

 [Home]
[Catalog of Products]
[Where to Start]
[Bonding Systems]
[Chip Floors]
[Chemical Resistance]
[Coatings]
[Conductive]
[Applications]
[Elastomeric Polyurethane Systems]
[Garage
Floors
] [High Temperature]
[Industrial Floors]
[Injection]
[Joint Systems & Sealants]
[Mortars / Grouts]
[Novolac]
[Polymer Systems]
[Primers Sealers]
[Misc.] [Seamless Flooring]
[Waterproofing]
[Dealers Wanted]
[Installation Tips]
[Product Guide]
[Wood Filler]
[Who We Are]
[Guide Specs]
[Tech Data Sheets in Acrobat Format]
[MSDS in Acrobat Format]

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s

%d bloggers like this: