Epoxy.com Product #1 – ESD

October 22, 2010

Epoxy.com Product #1 – ESD

Electro Static Dissipative Epoxy Coating

Ultra High Solids Epoxy Coating


Description

Epoxy.com Product #1 – ESD (Electrostatic Dissipative) Epoxy Coating for ESD Flooring is an ultra high solids bis-A epoxy floor coating designed to provide
electrostatic control properties to various surfaces including concrete or other nonconductive substrates. The use of a conductive primer will transmit conductive readings through
Epoxy.com Product #1 – ESD (Electrostatic Dissipative) Epoxy Coating for ESD Flooring if applied no thicker than 15 mils.

Epoxy.com Product #1 – ESD (Electrostatic Dissipative) Epoxy Coating for ESD Flooring provides excellent bond to concrete as well as high impact and wear.

Advantage

  • Easy Application
  • Dissipates a 5000 volt Charge to Zero in less than 0.1 Seconds @72°F
    and 12%RH.
  • Available in Static Dissipative Range of 1,000,000 to 1,000,000,000 ohms
    per EOS/ESD Standards.
  • Consistent Electrical Resistance Ratings When Tested at 10-500 Volts.
  • High Gloss
  • Good Abrasion Resistance.
  • Easy to Clean..

Considerations

Composition

Ultra High Solids Bis-A Epoxy Resin and Conductive Fillers.


Epoxy.com Epoxy Color Chart Here

Color Selection

Epoxy.com Product #1 – ESD (Electrostatic Dissipative) Epoxy Coating for ESD Flooring is available in Epoxy.com Colors listed to the right. Custom colors available as approved.

Application

Surface Preparation

Surface preparation is considered to be the most important step of any
resinous flooring application. Improper surface preparation could turn what
seems to be a simple process into a lengthy, difficult repair. See Epoxy.com
Surface Preparation Guide
for proper surface preparation
procedures.  When in doubt you should always contact Epoxy.com Technical
Support with your questions.

Installation

<!–

Prime concrete surfaces with Epoxy.com Product #899 at
a rate of 250-300 SF per gallon and allow to dry to the touch.

–>

Epoxy.com Product #1 – ESD (Electrostatic Dissipative) Epoxy Coating for ESD Flooring is normally spread with a
trowel or squeegee and back-rolled with a 3/8� medium nap roller. Care should be taken to minimize the entrapment of air caused by
over rolling.

Clean Up

Clean skin with soap and water. Tools and equipment should be cleaned with xylene or lacquer thinner.

Coverage

Epoxy.com Product #1 – ESD (Electrostatic Dissipative) Epoxy Coating for ESD Flooring will yield 12-15 mils
when spread at 100-130 sq ft/gal. 15 mils is considered the maximum thickness.

Maintenance

After completing the application of Epoxy.com Product 100MR Moisture Tolerant Primer and Base Coat and the topcoats or floor covering system, the installer
should provide the owner with maintenance instructions relevant to the specific topcoats or floor covering. If floors become slippery due to
animal fats, oil, grease, or soap film, clean and rinse thoroughly.

Availability

Contact Epoxy.com Customer Service Department.

Physical Data

Flammability ASTM D-635 Self Extinguishing
Fungus & Bacteria Growth Mil-F 52505�4.4.2.11 Will not support growth of fungus or bacteria

when subjected to mildew

Hardness ASTM D-2240 70-80 Shore D
Bond Strength to Concrete ASTM D-4541 Greater than 300psi (100% concrete failure)
Water Absorption ASTM D-570 Nil
Thermal Shock Resistance ASTM C-884 Passes
Abrasion Resistance ASTM D-6040 75-100mgs
Impact Resistance ASTM D-2794 100 in-lbs direct

Technical Data

Pot Life 35-40 Min. (@73°F)
Foot Traffic 14-16 hours (@73°F )
Complete Cure 5 days (@73°F.)
VOC Content Less than 50gm/l
Weight per Gallon 10.5-11 lbs per gal.
Glass, 60° Greater than 80

Technical Service

Contact Epoxy.com Technical Support Department

For more information Contact:

Norm Lambert
President &
Director of Technical Support
Epoxy Systems, Inc
Available by Phone M-F 9AM-4PM Eastern Time (6 AM – 1 PM Pacific Time)
352-533-2167 (Voice)
352-465-3497 (fax)
norm@epoxy.com
[Catalog of Products]
[Where to Start]
[Guide Specs]
[Epoxy Installation Guides]
[Epoxy Bonding Systems
]
[Chip Floors]
[Chemical Resistant Epoxy]
[Seamless Coatings] [Conductive Epoxy Flooring]
[Crack Injection of Concrete & Wood]
[ Epoxy Applications]
[Elastomeric Polyurethane Systems]
[Seamless Garage Flooring Resins]
[High Temperature Resins]
[Seamless Industrial Floors] [Joint Systems & Sealants]
[Methyl Methacrylate MMA ]
[Novolac Epoxy Resins]
[Epoxy Mortars & Grouts]
[Primers Sealers]
[Seamless Flooring]
[Waterproofing]
[Dealers Wanted]
[Epoxy Installation Tips]
[Who We Are]


New Epoxy.com Electro Static Dissipative Epoxy

September 1, 2010

Epoxy.com announces a new ESD Epoxy Product

New Epoxy Electrostic Dissipative (ESD) Epoxy Coating

Less Expensive, Easier to Use, More Durable


Epoxy.com Product #677

Electro Static Dissipative (ESD) /CONDUCTIVE COATING


DESCRIPTION

Epoxy.com Product #677 is a pigmented, water-based epoxy coating designed to achieve either an electro-static dissipative (ESD) finish or conductive finish by
modifying the underlying system components and thickness. Epoxy.com Product #677 has very low odor making it suitable for use in occupied
buildings and has high bond strength and adhesion to concrete and other surfaces.

ADVANTAGES

  • Durable, Attractive, Chemical Resistant, Non-Porous, Light Reflective Finish.
  • Low Odor during application and cure.
  • Maintains Electrical Conductivity Performance over the Wear Life of the System
  • Fast Dry and Re-coat Time.
  • Easy Clean-up.
  • Provides an ESD finish in the range of 1,000,000 to 1,000,000,000 ohms resistance when used over a non-conductive
    primer/basecoat or a conductive finish in the range of 25,000 to 1,000,000 ohms resistance when used over a conductive primer/basecoat.

CONSIDERATIONS

  • Substrate must be above 50°F and relative humidity below 85% for proper curing.
  • Substrate must be free of dirt, waxes, curing agents and other foreign materials.
  • Excessive moisture in the substrate will require a moisture vapor control treatment.

TYPICAL USES

Concrete floors and walls in electronic component assembly areas, data processing, military/aerospace, pharmaceutical plants,
hazardous industries (dust or explosion hazards). For use in any areas where the build-up of static electricity is a concern or a spark-proof floor is required.

APPLICATION

SURFACE PREPARATION

Surface Preparation is the most critical portion of any successful resinous flooring system application. All
substrates must be properly prepared and tested for moisture as outlined in Epoxy.com
Surface Preparation Guidelines.

INSTALLATION

Mix Part B of Epoxy.com Product #677 prior to combining. Mix 1 part Part A with 2 parts Part B. Epoxy.com Product #677 at a rate of 200 ft2
per gallon per coat with a short nap roller. Care should be taken to avoid
puddles. Two coats are necessary to insure uniform coverage.

Epoxy.com Product #677 Thin-Film ESD Epoxy Coating System 12-15 Mils(1,000,000-1,000,000,000 ohms)

Material Qty./ 1000 SF Coverage
1. Epoxy.com Product #899 Epoxy Primer 4-5 gallons 200-250 SF /gallon
2. Epoxy.com Product #677 ESD/Conductive Epoxy Coating 5 gallons 200 SF /gallon
3. Epoxy.com Product #677 ESD/Conductive Epoxy Coating 5 gallons 200 SF /gallon

CLEAN-UP

Clean skin with soap and water. Tools and equipment should be cleaned with warm soapy water, xylene or lacquer thinner. Consult Material Safety Data for safety and health precautions.

COMPOSITION

Waterborne Epoxy Resin and Conductive Fillers

COVERAGE

Epoxy.com Product #677, when applied at 200 SF per gallon, yields 5.2 �to 6.0 mils dry film thickness.

TECHNICAL DATA

Viscosity @ 75°F 600-1000 CPS
Mixing Ratio 1 Part A to 2 Parts B by Volume
Solids Content, by volume 50-55%
Volatile Organic Content (VOC) <20 gm/L
Bond Strength to Concrete 400-500 psi (100% concretefailure
Weight per Gallon, mixed 8.75-9.00 pounds per gallon, mixed

CURE/DRY TIME

Pot Life 20-30 min.
Dry to touch 6 hours @ 75°F
Recoat 8-24 hours @ 75°F
Light Traffic 24 hours @ 75°F
�H� Hardness 2 days
�5-H� Hardness 30 days

AVAILABILITY

Contact Epoxy.com Customer Service Department at 321-206-1833

Maintenance

Remove animal fats, oil, grease or soap film promptly to reduce slipperiness. Epoxy.com Product #677 can be cleaned with neutral soaps and detergents.
If long periods of heavy traffic cause wear patterns reapply as need.
Anti-skid materials will reduce the effectiveness of the static dissipative
properties of this material.  Do not use aggressive anti-skids. It is
impossible to get an accurate reading of the conductivity of the floor if
anti-skids are used.

Technical Services

Contact Epoxy.com Technical Support with your questions about this
product at 352-533-2167. Epoxy.com Technical Support Department can help you
with the selection, specification, installation, and maintenance of
Epoxy.com products, or visit http://www.epoxysystems.com.

Norm Lambert
President &
Director of Technical Support
Epoxy Systems, Inc
Available by Phone M-F 9AM-4PM Eastern Time (6 AM – 1 PM Pacific Time)
352-533-2167 (Voice)
352-465-3497 (fax)
norm@epoxy.com

 [Home]
[Catalog of Products]
[Where to Start]
[Bonding Systems]
[Chip Floors]
[Chemical Resistance]
[Coatings]
[Conductive]
[Applications]
[Elastomeric Polyurethane Systems]
[Garage
Floors
] [High Temperature]
[Industrial Floors]
[Injection]
[Joint Systems & Sealants]
[Mortars / Grouts]
[Novolac]
[Polymer Systems]
[Primers Sealers]
[Misc.] [Seamless Flooring]
[Waterproofing]
[Dealers Wanted]
[Installation Tips]
[Product Guide]
[Wood Filler]
[Who We Are]
[Guide Specs]
[Tech Data Sheets in Acrobat Format]
[MSDS in Acrobat Format]


Listing of Epoxy.com Epoxy Calculators

July 30, 2010

List of Epoxy.com Calculators

A current listing of Epoxy.com Material Calculators to date. Include Calculators for Epoxy.com Coatings, Epoxy.com Cove Base, Epoxy.com Dowel Bar Adhesives, Epoxy.com Stone Overlay Adhesive, Epoxy.com Table top Resin, Epoxy.com Tile Grout, Epoxy.com Table Top and Casting Resin, and Epoxy.com Electrical Potting and Casting Resin.


Epoxy.com New Calculators for ESD and Conductive Flooring

July 29, 2010

Epoxy.com Conductive Coatings and
Epoxy.com Electrostatic Dissipative Coatings

Electrostatic Dissipative (ESD) – 1 Million to 1 Billion OhmsConductive Epoxy – 100,000 to 1 Million Ohms


Epoxy.com announces its new Electrostatic (ESD) and Conductive Flooring Calculator.  All you have to know is the square footage that you have, and the type of flooring system you need and the calculator will help you estimate the material needed.

Please contact me with your questions.

Norm Lambert
President & Director of Technical Support
Epoxy Systems, Inc
Florida & Vermont USA
Available by Phone M-F 9AM-4PM Eastern Time (6 AM – 1 PM Pacific Time)
352-533-2167 (Voice)
352-465-3497 (fax)
norm@epoxy.com
www.epoxy.com     New Secure Login
Subscribe to Epoxy.com News Feed – Get the latest product information, tricks and tips delivered directly to you via your favorite news reader.


Epoxy.com Announces New Conductive Novolac Chemical Resistant Epoxy Flooring System

April 9, 2010

Epoxy.com a division of Epoxy Systems, Inc. announces that it has added  Epoxy.com Product #676 Novolac Epoxy Chemical Resistant Conductive Floor Coating to the Epoxy.com line of Conductive Resins.  Epoxy.com Product #676 is a 100% solids – Zero (0) VOC epoxy Novolac Chemical resistant conductive (anti-sparking) epoxy flooring and floor coating system ideal for severe chemical and solvent storage requiring a chemically resistant conductive and spark resistant surface.

 Applied at a nominal 1/16”, Epoxy.com Product #676 Novolac Epoxy Chemical Resistant Conductive Floor Coating offers the superior chemical resistance of an Epoxy.com  Novolac Epoxy Resin System while maintaining a conductive surface.

ADVANTAGES

  • Low viscosity for improved handling during application.
  • Exhibits excellent resistance to strong acids, alkalis and most industrial chemicals and solvents.
  • 100% Solids—low odor application and cure (0-VOC).
  • Bonds well to cool, damp substrates.
  •  Conductive & non sparking, 25,000 to 1,000,000 ohms resistance.

CONSIDERATIONS

  • Substrate  to receive Epoxy.com Product #676 Novolac Epoxy Chemical Resistant Conductive Floor Coating temperature must be a minimum of 50°F.
  • Substrate must be free of dirt, waxes, curing agents and other foreign materials.
  • Steel surfaces to receive Epoxy.com Product #676 Novolac Epoxy Chemical Resistant Conductive Floor Coating must be free of grease and oils.  Abrasive blast to SSPC-SP-3.
  • Refer to Epoxy.com Surface Preparation Guidelines for  substrate requirements.

COMPOSITION

100% Solids, modified polyamine, cured epoxy novolac resin and fillers

APPLICATION

SURFACE PREPARATION

Surface Preparation is the most critical portion of any successful resinous flooring system application.  All substrates must be properly prepared as outlined in Epoxy.com Surface Preparation Guidelines.  Contact epoxy.com  technical service department is pleased to answer any questions.

INSTALLATION

Installation of Epoxy.com Product #676 Novolac Novolac Epoxy Chemical Resistant Conductive Floor Coating will vary with application.  Normally spread with a trowel or squeegee and lightly back-rolled with a medium or short nap roller.  Care should be taken to minimize the entrapment of air caused by over rolling. For complete instructions, consult installation guide or Epoxy.com Technical Support Department

CLEAN-UP

Clean skin with soap and water.  Tools and equipment should be cleaned with xylene or lacquer thinner.

COVERAGE

Epoxy.com Product #676 Novolac Epoxy Chemical Resistant Conductive Floor Coating will yield approximately 32 mils when spread at 50 ft2 per gallon.  Two coats required.

COLOR

Epoxy.com Product #676 Novolac Epoxy Chemical Resistant Conductive Floor Coating is available in Standard Colors and Custom Colors as approved.

TECHNICAL DATA

Viscosity @ 75°F 1,000-1,500 cps
Mixing Ratio by volume 2 Part A to 1 Part B by Volume
Solids Content by volume     100% by volume
Volatile Organic Content 0
Weight per gallon, mixed 11.0-11.5 lbs. per gallon mixed

CURE/DRY TIME

Pot Life 20-25 min. @75°F
Dry to Touch 6-7 hours @ 75°F
Re-Coat 8-12 hours @ 75°F
Light Service 24 hours @ 75°F
Full Cure & Maximum Resistance     5 days

CHEMICAL RESISTANCE

REAGENT

RATING

Acetic Acid-10%, 30% R
Acetone L
Ammonia Hydroxide-38% R
Beer R
Bleach L
Brake Fluid R
Citric Acid-30% R
Citric Acid-40% R
Crude Oil R
Diesel Fuel R
Ethylene Glycol R
Fatty Acids R
Gasoline R
Hydrochloric Acid-37% R
Lactic Acid-50% R
Lactic Acid-80% R
Methyl Ethyl Ketone R
Methylene Chloride L
Nitric Acid-10% R
Peroxide-35% R
Phosphoric Acid R
Skydrol R
Sodium Hydroxide-50% R
Sulfuric Acid-98% R
Toluene R
Urea R
Vinegar R
Xylene R
R-Recommended for continuous service
L-Limited Recommendation, occasional spills
*-May cause slight stain or discoloration

MAINTENANCE

After completing the application of Epoxy.com Product #676 Novolac Epoxy Chemical Resistant Conductive Floor Coating, the installer should provide the owner with maintenance instructions. Epoxy.com Product #676 Conductive Chemically Resistant Novolac Floor Coating is easily cleaned with neutral soaps or detergents.

For more information please contact Epoxy.com Technical Support at: 352-533-2167 or email them at info@epoxy.com


%d bloggers like this: