Epoxy Over Epoxy

June 28, 2016

A customer writes: “I installed your Product #1 All Purpose Epoxy Coating on our floor about 20 years ago.  The floor is not warn out or pealing.  It does have scratches where pallets with nails sticking out the bottom has scratched the surface. I want to change the color to our company color anyway, so I want to re-coat the whole floor. How do I proceed from here?”

You will want to sand the existing floor removing all the shine.  It sounds like there was quality installation and surface prep, since you have no lifting or pealing. If you should have any that is loose you need  to completely remove loose coating .  Solvent wipe with Xylene. Lets solvent dry and apply your epoxy normally.

CAUTION:  Epoxy doesn’t like sticking to epoxy unless you do your surface prep meticulously.  I always recommend doing a test patch to test your surface preparation before you proceed with doing the rest of the floor. This can be done by placing a small test patch or patches. Let them harden overnight and then try removing them with a putty knife, screw driver of similar method to insure it is well bonded.

For more information please contact Epoxy.com Technical Support Department by email at: info@epoxy.com or by phone 353-533-2167.


Are Epoxy.com 100% Solids Epoxy Low VOC

June 23, 2016

A user writes: “I have seen a number of your products that are on a list or marked with a tag that says Zero (0) VOCs.  When I look at the data sheet it says that the Epoxy.com product is 100% Solids, but does not say it is Zero (0) VOCs.”

Norm Lambert > Thank you for pointing that out.  You bring up an excellent question.  Epoxy.com Products that are 100% solids (100% active ingredients) do not contain solvent, that means they have no VOCs making them compliant with the toughest Low VOC Standards. I will start updating pages on the Epoxy.com to reflect that in the future.  Until then please rest assured that all Epoxy.com Products that are 100% solids have no VOCs in them.


Epoxy Oil Stop Primer

May 13, 2016
Epoxy_oil_stop_primer

Oil Saturated Concrete

 

Oily contaminated concrete is very difficult to bond to, but it can be done with special care and Epoxy.com Product #201 Oil Stop Primer.  Plant floors, warehouse floors, commercial, and residential garage floors can all have this problem.  Here is a typical question that I get about oil contaminated floors:

“We were looking at your product because we have a floor in a maintenance garage that is pretty well soaked with oil.  A new tenant is going into that space so we know that there needs to be something to allow the new floor to stick and to stop the odors.”

Here is my typical response:

Is the oil saturation petroleum oil? If so you need to:

  1. Degrease the floor
  2. Mechanically clean the floor – www.epoxy.com/surfaceprep.aspx.
  3. Apply 1 coat of Epoxy.com Product #201 – www.epoxy.com/201.aspx – at a rate of 200-320 SF per gallon.
  4. Inspect for bond the next day. If bond fails remove the loose #201 and go back to step one.
  5. If bond is good check for oil on top of the primer.  If there is oil on top of the #201 and it is well bonded remove the oil with xylene or other effective degreaser.
  6. Coat with 2 coats of Epoxy.com Product #2 – www.epoxy.com/2.aspx.

I like the Product #2 for these applications because it is very resistant to petroleum oils. Depending on your specific application the material you use over the #201 can be a number of different flooring, coating systems or chemical resistant epoxy floor systems.

For more information, please visit our website at www.Epoxy.com, contact our technical support department at 352-533-2167 or email me at norm@epoxy.com for a specific recommendation.

 


Choosing the Right Epoxy Sealer

May 18, 2015

Having the knowledge of which type of sealer to use is extremely important to the overall satisfaction of the job. There are 3 basic types of epoxy sealers. The first is 100% solids epoxy, solvent based sealants and finally water based sealers. There are also urethane and acrylic sealers.

To understand how each sealant works one must understand how they act as an epoxy. http://www.epoxy.com/primersealer.aspx . The 100% solids epoxy when applied to a floor retains a consistent thickness. Epoxy.com #15 http://www.epoxy.com/15.aspx is the best product for maintaining a clear epoxy sealer without any loss of thickness due to evaporation. If you roll a gallon of material on your floor, when it hardens you maintain the thickness of the full gallon of spread coverage.

Epoxy.com #15 can be used to seal previously installed epoxy and river rock stone on pool decks or walkways. It also seals Epoxy Chip flooring, as well as acts as a binger and sealer to Epoxy quartz flooring. It provides protection, just the right amount of shine and helps to keep the water from permeating the underlying concrete. It also works well inside in garages. It is our most versatile sealer that we offer it works great on concrete inside and when properly installed outdoors.

When you apply a water based sealer or solvated sealer you will consistently loose a percentage of the thickness due to evaporation. Even though this is the case there are times when a 100% solids epoxy may not do exactly what you need it to accomplish. In this case we offer products with different components and viscosity to suit your needs as a consumer.

Epoxy.com #671  is a low viscosity, two component, carbon filled, polyamide modified conductive primer/sealer formulated with special wetting agents to provide maximum penetration into concrete surfaces. Product #671 Primer Sealer is ideal for both new and old concrete surfaces. Product #671 Conductive Epoxy Primer Sealer provides excellent resistance to wear, and can be used either alone or as a conductive sealer or as a conductive epoxy primer when used with Product #674 Electro-Static Dissipating Urethane Topcoat and our Conductive Systems.

Epoxy.com #80 is a solvented clear acrylic solution formulated to create a clear, non-yellowing protective coating. Product #80 ACRYLIC SEALER http://www.epoxy.com/acrylic-sealer.aspx provides a tough, UV and abrasion resistant film that effectively protects surfaces from moisture penetration, staining, dirt, dust, and wear. It is good for both indoor as well as outdoor applications. This works well to seal existing terrazzo floors and as well as slate.

For those in California, who don’t want to use a 100% solid material, we offer Epoxy.com http://www.epoxy.com/High-Solids-Urethane-Coating.aspx Epoxy.com # 441 is free of the health and environmental problems normally found in solvent-based urethanes, while maintaining excellent performance properties. The very low VOCs allows this urethane coating to meet the strict low VOC standards. Epoxy.com # 441 Polyurethane Coating and Sealer provides a matte finish. Product #441 water-based urethane coating and sealer has good chemical, stain, and mar resistance.

Finally the most important thing to remember when you are choosing an Epoxy.com Sealer is to make sure you are using The Right Product for The Right Job. If you would like assistance with your selection please call our Technical Support Line at 352-533-2167 and we will be happy to assist you.


%d bloggers like this: