Epoxy Injection of Structures Part 2

February 14, 2017

Infrastructure Repairs Using Epoxy

Epoxy Concrete Injection Epoxy Wood Injection, epoxy crack repair

Epoxy Structural Concrete and Wood Repair / Waterproofing

The following article is written with enough information about resin injection systems to help protect the Owner from the misuse or improper installation of an injection systems.   For more information contact me: Norm Lambert.

This is the second in a series on Infrastructure Repairs Using Epoxy. Part One was Introduction to Epoxy Injection.  If your have not read that yet you may want to go back and read it before you proceed with reading this.

Part 2: Crack Analysis Before Epoxy Injection

As with all repair and rehabilitation of concrete, the initial job analysis is by far the most important step. Epoxy Injection Resin will weld concrete cracks but, of course, will not repair the cause of the cracking.

Analyze each potential injection application to determine the exact cause or causes of the cracking. Correcting the cracking problem can be fairly simple, or may be difficult involving design changes.

Consult a structural engineer when design changes are necessary. Do this before starting the injection. Repairing cracks by Injection is effective after these design changes. Prevent future cracks by fixing the original cause of the cracking, when ever possible.

Parking garages are an example of cracking problem that require a structural engineering analysis.Epoxy.com Epoxy Inection Often inadequate design for expansion/contraction is the cause for parking garage structural cracking. Avoid weld injecting a crack if there are not enough expansion joints. Sometimes flexible overlays such as Epoxy.com System # 495 can be used to overcome this defect. This does not however encapsulate the rebar in a way that will totally stop the premature deterioration of the steel. Often times additional joints are needed, thus the analysis of cracking problems is critical.

Bridge decks and slab on grades can often be repaired with Epoxy.com Product #684LV crack healer and sealer and save some of the cost of doing epoxy injection.

Next in the Injection Series:

Part 3: Setting Epoxy Injection Ports

For more information visit our website at http://www.epoxy.com, email us at info@epoxy.com or call our technical service department at +1 (352) 533-2167.

Concrete Crack Healer & Sealer

February 9, 2017

Repair Cracks in Bridge Decks

And Similar Horizontal Concrete Surfaces

Low Viscosity Fast Setting Methyl Methacrylate (MMA)

Permanent Crack Repair System

MMA CONCRETE CRACK HEALER and SEALER Product #684LV is a 100% reactive ultra-low viscosity methyl methacrylate resin used as a penetrating crack sealer or to fortify extremely porous concrete substrates. MMA CONCRETE CRACK HEALER and SEALER Product #684LV is typically used on bridge decks, parking structures, concrete floors or as a general penetrating sealer to prevent moisture intrusion.

MMA CONCRETE CRACK HEALER AND SEALER Product #684LV is a reactive methacrylate resin, which hardens rapidly with the addition of Product #695 MMA HARDENER, even at low temperatures.


  • Fast Cure (60 min.) for Rapid Recoat and Return to Service
  • Ultra-Low Viscosity for Excellent Absorption Into Concrete
  • Protects Against Water Penetration
  • VOC Compliant (100% Solids)
  • Full Strength in 1 Hour
  • Use Over Wide Temperature Range – Even Below Freezing – Adjust for Temperature in the Field


  • Substrate must be dry and free of dirt, waxes, curing agents and other foreign materials.
  • Should not be installed on fresh concrete until maximum shrinkage has occurred (at least 30 days after placement).


MMA CONCRETE CRACK HEALER and SEALER Product #684LV is a 100% reactive methyl methacrylate resin. Color is supplied is clear.


  • Bridge Decks
  • Containment Structure Floors
  • Plant Floors
  • Concrete Slab on grade
  • Suspended Concrete Slab
  • Virtually any horizontal concrete surface

For more information about repairing infrastructure visit our website at: http://www.epoxy.com, email us at info@epoxy.com or phone technical support at +1 (352) 533-2167

%d bloggers like this: