Selecting the Right Floor for a Mechanical Room

July 27, 2015

Mechanical Room Floors are very unique in their use and conditions. You have to consider the installation environment and the function of the floor. Our Mechanical Room Floor will protect the concrete, and contain any liquids that spill.

Systems used in mechanical rooms should be zero VOC. You do not want solvent evaporating from your material. Evaporated solvent could be picked up by your air handling unit sending it through your building. The best way to prevent this is with a VOC free 100% solids resin system. A resin system that is 100% solids has no solvent (or water) in it. It also means when you spread a gallon of material on your floor after it hardens you still have a gallon of material. With water-based and solvent based materials you lose half the material to evaporation.

Mechanical rooms should be chemical resistant. Typically they are top coated with Epoxy.com Product #2 Chemical Resistant Epoxy – www.epoxy.com/2.aspx. If it is a chemical feed room you can supply a list of chemicals and concentrations to the technical support department so you can make sure the #2 is chemical resistant enough.

The systems used for mechanical rooms are impact resistant. The limiting factor is the strength of the concrete substrate. Properly installed the epoxy will stay bonded to the concrete. The only way the epoxy can chip is if you chip the concrete from underneath the epoxy. You can install a thicker epoxy floor for an additional cost if you think you need still additional protection.

The systems recommend for mechanical rooms are highly abrasion resistant and will easily handle traffic up to heavy fork lift traffic. The system can be made even thicker if you have an unusual amount of abusive traffic.

When the mechanical room is over a finished space, it is suggested that a crack isolation membrane be integrated into the system. This can be done with Product #32 Epoxy Membrane System. The advantage of #32 Epoxy Membrane Resin as part of the system is 100% solids and has zero VOCs.

If the mechanical room is shut down and you can handle solvent and want something still more flexible you can use Epoxy.com Product #459 a two component, high solids, elastomeric urethane instead of or in addition to the Product #32 Epoxy Membrane above. Product #459 exhibits excellent elongation properties along with high tensile strength and tear resistance to make it an ideal crack resistant membrane for use under Product #2 and all of our other epoxy mechanical room floor coatings.

One of the primary reasons you need a mechanical room floor over finished space below is to waterproof it. The above methods accomplish the waterproofing in the center of the floor. The edges of the floor can be protective with a coving material up the wall and around pipe penetrations. That can be accomplished with Product #720 Epoxy Coving Resin System which can be used to install an integral cove base for all of our epoxy based mechanical room flooring and most of our other epoxy flooring and coating systems. This provides seamless wall to floor protection.

For more information on seamless water and chemical resistant mechanical room flooring, contact Epoxy.com Technical Support Department at 352-533-2167, or email me at norm@epoxy.com.

 


Choosing the Right Epoxy Sealer

May 18, 2015

Having the knowledge of which type of sealer to use is extremely important to the overall satisfaction of the job. There are 3 basic types of epoxy sealers. The first is 100% solids epoxy, solvent based sealants and finally water based sealers. There are also urethane and acrylic sealers.

To understand how each sealant works one must understand how they act as an epoxy. http://www.epoxy.com/primersealer.aspx . The 100% solids epoxy when applied to a floor retains a consistent thickness. Epoxy.com #15 http://www.epoxy.com/15.aspx is the best product for maintaining a clear epoxy sealer without any loss of thickness due to evaporation. If you roll a gallon of material on your floor, when it hardens you maintain the thickness of the full gallon of spread coverage.

Epoxy.com #15 can be used to seal previously installed epoxy and river rock stone on pool decks or walkways. It also seals Epoxy Chip flooring, as well as acts as a binger and sealer to Epoxy quartz flooring. It provides protection, just the right amount of shine and helps to keep the water from permeating the underlying concrete. It also works well inside in garages. It is our most versatile sealer that we offer it works great on concrete inside and when properly installed outdoors.

When you apply a water based sealer or solvated sealer you will consistently loose a percentage of the thickness due to evaporation. Even though this is the case there are times when a 100% solids epoxy may not do exactly what you need it to accomplish. In this case we offer products with different components and viscosity to suit your needs as a consumer.

Epoxy.com #671  is a low viscosity, two component, carbon filled, polyamide modified conductive primer/sealer formulated with special wetting agents to provide maximum penetration into concrete surfaces. Product #671 Primer Sealer is ideal for both new and old concrete surfaces. Product #671 Conductive Epoxy Primer Sealer provides excellent resistance to wear, and can be used either alone or as a conductive sealer or as a conductive epoxy primer when used with Product #674 Electro-Static Dissipating Urethane Topcoat and our Conductive Systems.

Epoxy.com #80 is a solvented clear acrylic solution formulated to create a clear, non-yellowing protective coating. Product #80 ACRYLIC SEALER http://www.epoxy.com/acrylic-sealer.aspx provides a tough, UV and abrasion resistant film that effectively protects surfaces from moisture penetration, staining, dirt, dust, and wear. It is good for both indoor as well as outdoor applications. This works well to seal existing terrazzo floors and as well as slate.

For those in California, who don’t want to use a 100% solid material, we offer Epoxy.com http://www.epoxy.com/High-Solids-Urethane-Coating.aspx Epoxy.com # 441 is free of the health and environmental problems normally found in solvent-based urethanes, while maintaining excellent performance properties. The very low VOCs allows this urethane coating to meet the strict low VOC standards. Epoxy.com # 441 Polyurethane Coating and Sealer provides a matte finish. Product #441 water-based urethane coating and sealer has good chemical, stain, and mar resistance.

Finally the most important thing to remember when you are choosing an Epoxy.com Sealer is to make sure you are using The Right Product for The Right Job. If you would like assistance with your selection please call our Technical Support Line at 352-533-2167 and we will be happy to assist you.


%d bloggers like this: