Epoxy.com Product #693 Methyl Methacrylate Coating

Epoxy.com Product #693

Methyl Methacrylate (MMA) Coating

For Top Coating All Epoxy.com Methyl Metacrylate Systems


Epoxy.com Product #695 Methyl Methacrylate (MMA) Coating is
a 100% reactive, medium viscosity methyl methacrylate resin developed as a
topcoat for exterior or interior use with Epoxy.com MMA Systems.  Epoxy.com
Product #695 Methyl Methacrylate (MMA) Coating is semi-flexible for outside use
and will not yellow after
curing. Its excellent clarity makes it ideal for sealing color quartz and vinyl
flake systems. It is excellent for
exterior applications such as parking decks, concrete and steel stairs, ramps,
and numerous other applications.


  • Parking decks
  • Steel and Concrete Stairs
  • Ramps
  • Wooden and Concrete Decks
  • Balconies
  • Driveways


  • Low temperature accelerators are available for positive cures at temperatures from 32° to 55°F.
  • Excellent resistance to a wide range of chemicals.
  • Easy to apply by conventional painting techniques.
  • Clear after curing.
  • Suitable for USDA food handling areas.
  • Quick recoat time 45 minutes to 1 hour.
  • Flexibility makes it ideal for cold temperature, over wood, and outside


  • Concrete must be dry, free of dirt, waxes, curing agents and other foreign
  • Do not store outside in direct sunlight, storage temperature must be < 80°F.
  • Substrate must be completely dry.
  • On or below grade installation must have an efficient vapor barrier under
    the slab (minimum 10-15 mil).
  • Moisture vapor transmission must be less than 3 pounds per ASTM-F-1869
    and less than 80% RH per

ASTM F-2170.


Epoxy.com Product #693 Methyl Methacrylate (MMA) Coating is a 100% reactive
methyl methacrylate resin.



Surface Preparation is the most critical portion of any successful resinous flooring system application. All
substrates must be properly prepared as outlined in
Epoxy.com Surface Preparation Guide.


Epoxy.com Product #693 Methyl Methacrylate (MMA) Sealer and Coating requires
the addition of  Epoxy.com Product #695 MMA Hardener to start the hardening
process. The amount of hardener must be adjusted to the respective surface temperature (see table
below). At temperatures below 40�F, Epoxy.com Product #696 Accelerator must be used in addition to the amount of hardener used at
the 40�F level (about � oz by
vol./gal. @ 32°F up to 2.0 oz by vol./gal. @ -20°F).

For Epoxy.com Product #693 MMA Resin

Temp. (°F) of Resin,

Air & Floor SurfaceHardener % by Wt.

Based on Wt. of

#693 ResinHardener by Vol.

(oz.) Based on

Gallon of #693 ResinPot Life (min.)Harden Time (min.)+403.05.5Approx. 40Approx. 60+502.54.5Approx. 30-35Approx. 50+602.03.5Approx. 25-30Approx. 45+701.02.0Approx. 20Approx. 40

Epoxy.com Product #693 Methyl Methacrylate (MMA) Coating  must be applied 50-100 sq. ft./gal. (16-32 mils) for safe
through-hardening. To avoid yellowness do not apply more than 80 mils (20 sq ft/gal.).
For outdoor applications add 1% Epoxy.com Product #693 UV Inhibitor at a
rate of 1% by volume. Pigmented topcoats are achieved by adding pigment packs (1 quart per 5 gallons
resin) to Epoxy.com Product #693 Methyl Methacrylate (MMA) Coating.
Apply material with a notched trowel or squeegee and back roll with a short nap
mohair roller.


Clean skin with soap and water; use MEK, xylene, or clean proprietary epoxy thinners for equipment.
Consult Material Safety Data Sheet for safety and health precautions.


will yield 16-32 mils at 50-100 square feet per gallon, average.


Contact Epoxy.com Sales Department



Working Life 20-40 min. will vary with Temp

& amount of hardenerRecoat time45-60 minutesSolids Content100%Mix RatioSee chart aboveViscosity220-225 cps approx.Weight Per Gallon8.1 lbs.


Epoxy.com Product #693 Methyl Methacrylate (MMA) Sealer and Coating is considered to be a low maintenance flooring solution. Certain textures and environments,
however, require specific cleaning with bristled brushes. Due to the thermoplastic character of MMA resins,
black marks can occur from fork lifts and tires skidding.


Store in a cool and dry place, below 80°F, out of direct sunlight. Do not store near open flame or food. Shelf life
is 6 months in the original unopened containers.


Adequate cross ventilation should be provided. Good ventilation during the processing ensures a good cross
linking and hardening. Read, understand and follow Material Safety Data Sheets and Application Instructions
prior to use.

Use only as directed. If substrate and/or material temperature is above 90°F, DO NOT apply material.

Keep Out of Reach Of Children

Contact Epoxy.com Technical Support with your questions about this
product at 352-533-2167. Epoxy.com Technical Support Department can help you
with the selection, specification, installation, and maintenance of
Epoxy.com products, or visit http://www.epoxy.com/.

Norm Lambert
President &
Director of Technical Support
Epoxy Systems, Inc
Available by Phone M-F 9AM-4PM Eastern Time (6 AM – 1 PM Pacific Time)
352-533-2167 (Voice)
352-465-3497 (fax)
[Catalog of Products]
[Where to Start]
[Guide Specs]
[Epoxy Installation Guides]
[Epoxy Bonding Systems
[Chip Floors]
[Chemical Resistant Epoxy]
[Seamless Coatings] [Conductive Epoxy Flooring]
[Crack Injection of Concrete & Wood]
[ Epoxy Applications]
[Elastomeric Polyurethane Systems]
[Seamless Garage Flooring Resins]
[High Temperature Resins]
[Seamless Industrial Floors] [Joint Systems & Sealants]
[Methyl Methacrylate MMA ]
[Novolac Epoxy Resins]
[Epoxy Mortars & Grouts]
[Primers Sealers]
[Seamless Flooring]
[Dealers Wanted]
[Epoxy Installation Tips]
[Who We Are]

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s

%d bloggers like this: