NOVOLAC EPOXY WALL COATING – 100% SOLIDS

January 23, 2017

High Chemical Resistance Epoxy Coating

Epoxy.com Product #633W


Introducing highly chemically resistant Novolac epoxy wall coating.  Bring your chemical resistance to new heights. Apply this Novolac Epoxy Wall Coating on walls in thicker coats, with less runs.  Same great chemical resistant Novolac Epoxy as Product #633, but thicker.

Description

Epoxy.com Product #633W is a 100% solids epoxy novolac coating ideal for harsh chemical and solvent environments. “W” designates High Viscosity formulation for improved film build on vertical surfaces. Epoxy #633W can be used as a seal coat for various Epoxy.com products and systems where extreme chemical resistant performance is required, such as secondary containment, solvent storage, pump pads, trenches, chemical process areas, and other high exposure areas.

Epoxy Novolac Wall Coating is 100% solids, modified amine adduct cured epoxy novolac (novolac epoxy) resin.

Advantages

  • Exhibits excellent resistance to strong acids, alkalis, and most industrial chemicals and solvents.
  • Can be applied in occupied facilities.
  • Can be applied in cool damp conditions.
  • Can be rapidly re-coated in ambient conditions.

Considerations

Good surface preparation is one of the most important parts of the installation of a high end coating. Be sure to follow our
Surface Preparation Guide before installing this product.

Installation

  1. Review and follow epoxy installation tips
  2. Properly prepare the substrate.
  3. Mix small batches of the material with 2 parts “A” and one part “B”, being sure to completely mix for 3 min. Mix only what you can use in half the potlife. Remember the bigger the batch the faster it will setup in your bucket
  4. Installation methods will vary from job to job. Typical application is by brush and quality roller.
  5. Contact Epoxy.com Technical Support with any questions that you have.

Physical Properties

Color See Color Chart
Gloss, 60°F 100
Solids Contentr 100%
Mix Ratio 2A to 1B by Volume
Pot Life 20 min @ 75°F
VOC 0.0

Dry Time

Foot Traffic @ 75°F 10-12 hours
Recoat #75&deg:F 4 hours minimum, 16 hours maximum
Exposures to Chemicals @ 75°F 5 days

Chemical Resistance

REAGENT

RATING

Acetic Acid 30% R
Acetone L
Methylene Chloride L
Crude Oil R
Diesel Fuel R
Ethylene Glycol R
Fatty Acids R
Gasoline R
Metyl Ethyl Ketone L
Hydrochloric Acid- 36% R
Urea R
Bleach R
Citric Acid R
Skydrol R
Sodium Hydroxide – 50% R
Sulfuric Acid – 98% R
Toluene R
Lactic Acid R
Nitric Acid 20% R
Xylene R
R = Recommended for Intermittent Immersion

L = Limited recommendation, occasional spills

Performance Properties

Tensile Strength ASTM-D-638 10,400 psi
Adhesion to concrete ACI Committee 403 300-440+ psi (100% concrete
failure)
Hardness ASTM-D-2240 86 Shore D
Abrasion Resistance ASTM-C-501 (CS-17 Wheel) 30 mg loss
Service Temperature MIL-D-3134F 180°F – 325&deg:F (Dry Heat)
Elongation 2.5%

For more information visit our website at http://www.epoxy.com, email us at info@epoxy.com or call technical support at: 352-533-2167.


Epoxy Installation Instructions

January 5, 2017

How to Install Epoxy.com Resin Systems


INSTALLING EPOXY RESIN SYSTEMS

Proper mixing and installation is critical to the best success of all epoxy products.  This page is to help you find the right installation information that you need to install Epoxy Resin Systems.

Surface Preparation for Epoxy Resin Installation

All quality installation start with quality surface preparationThis guide will help you to know how to properly prepare your substrate for installation of Epoxy or any other high quality resin system. Improper surface preparation could turn what seems to be a simple process into a lengthy, difficult repair.

Do and Don’t do with epoxy.

These guides will help you to not make the common mistakes that people do and the things the people don’t do that can lead to a problem or even a failure of your epoxy resin installation.

Job Supplies Required to Install Epoxy Resin Systems

This list is  a suggested list of the materials that you will need for most typical epoxy coating systems. This list is also useful for installing roller applied coating systems like Epoxy.com Chip Flooring.

Epoxy Installation Guides

Epoxy Chip Flooring System
Installation Guide

Epoxy Chip Flooring Installation Guide. Floors have a special role to play in interior design. The heavy technical demands made on floors often make the use of certain decorative products simply impossible. The use of color chips can change all that! Color chips are increasingly being used in combination with “wet” products such as Product #315 Seamless Polymeric Multi-Colored Flake Chip Floor Resurfacing System to create decorative floors with more to offer than other ornamental products…Quality! This installation guide takes you step by step through the installation of Epoxy Chip Flooring Product #315.

Product #1 High Build Epoxy Coating 21-27 mils – All Purpose Epoxy Floor Coating Installation Guide.

Product #1 All Purpose High Build Epoxy Floor Coating a two component, zero (0) VOC, 100% solids epoxy Hi-Build epoxy coating used for high foot traffic and light to moderate forklift traffic areas where abrasion resistance is required; for protection against mild corrosion and as a decorative waterproof coating for walls, floors, tanks, etc. Installation Guide For All Purpose High Build Epoxy Floor Coating #1.

1ESD / Conductive – Electrostatic Dissipative Epoxy Floor Coating Installation Guide

Conductive Epoxy Floor Coating Installation Guide –  Product #1ESD Epoxy Coating System consists of Product #899 Epoxy Primer followed with one finish coat of Product #1ESD/Conductive Epoxy Coating. Product #1ESD/Conductive is available in pigmented finish only. Product #1ESD Epoxy Coating System will test in the �ESD� range, between 1,000,000 and 1,000,000,000 ohms electrical resistance when Product #1ESD/Conductive is applied over a non-conductive primer (or non-conductive bodycoat), and produces a 12-15 mil thick ESD floor coating system. This guide will take tell you how to install the Conduct Epoxy Floor Coating.

Product  #2 High Chemical Resistance Epoxy Floor Coating Installation Guide

Chemical Resistant Epoxy Coating Product #2 is a two component, 100% solids, Zero “0” VOC epoxy chemical resistant coating used to protect chemical concrete, steel and other structural materials from non-oxidizing acids and alkalines for both interior and exterior applications.This guide will take take you through the steps to
install the Conduct Epoxy Floor Coating.

Product #15 Chemical Resistant Epoxy Quartz Flooring

Product #15 Chemical Resistant Quartz Flooring Installation – Single Broadcast Installation Method

Product #633 Novolac Highly Chemical Resistant Novolac Epoxy Floor Coating Installation Guide

Product #633 Novolac Epoxy Chemical Resistant Epoxy Coating is a 100% solids epoxy Novolac coating ideal for harsh chemical and solvent resistant applications. Product #633 Novolac Epoxy Chemical Resistant Epoxy Coating is used in secondary containment, solvent storage, pump pads, trenches, and other high exposure areas. This Installation Guide will help you install Product #633 Novolac Epoxy Chemical Resistant Epoxy Coating. You can also find more information with pictures about installation on this page the Epoxy.com Blog.

Epoxy Injection Installation

Epoxy Injection – This Guide will take you through the basics of doing epoxy injection.  Epoxy injection is one of the most economical, to make a structural repair and waterproofing in cracked concrete.

Additional Installation Guides

These are just a few or our most popular products for additional products and guides pleas contact us at:

 For more information visit our website at: www.epoxy.com , call technical support at 352-533-2167 or email us at info@epoxy.com.


%d bloggers like this: