November 20, 2012
Here is a suggested list of the materials that you will need for most typical epoxy coating systems. This list is also useful for installing roller applied coating systems like Epoxy.com Chip Flooring.
- 1 roller pan
- 6 inserts for roller pan
- 15 stir sticks
- 12 (5 QT) plastic pails
- 3 (5 G) plastic pails
- Roll of Duct Tape
- 5 heavy duty 9″ roller frames
- 6 (3/8″ nap) roller covers *be sure the roller nap doesnot fall apart in hands*
- Roller handle extension poll
- 4 Hard Plastic Body Filler type Squeegees
- Paper 6oz Dixie cups
- 2 (2 blade) mixing paddles – should be at least 5 inches in diameter and capable of being used in a heavy duty drill
- Heavy Duty Drill for mixing paddles above
- 6 (2″) paint brushes *check bristles to be certain they CAN NOT be pulled out*
- Latex (or non latex) rubber gloves
- Vacuum (Shop Vacuum Quality)
- Stiff Bristled Broom *check to make sure bristles do not fall out*
- Chalk line or laser to set lines that need to be masked
- Roll of plastic to keep buckets on to avoid drips onto floor
- Go Jo Hand cleaner or fast orange for hands and skin
*Note – Epoxy does NOT come out of fabrics*
For more information visit www.epoxy.com.
June 20, 2012
Epoxy.com calculators are designed for busy professional estimators who wants to quickly and accurately calculate the amount of epoxy or epoxy like material for their job.
Epoxy Coating Spread Rate Calculator shows how much 100% solids epoxy coating you will need for your installation.
Epoxy Dowel Bar and Anchor Bolt Adhesive Calculator shows the amount of epoxy adhesive you will need to install dowel bars into concrete or wood.
Epoxy Stone Overlay Calculator figures the amount of epoxy adhesive resin your will need to do an epoxy stone overlay.
Epoxy Table Top Resin Calculator figures the amount of epoxy table top resin you will need to do a table or bar top.
Epoxy Tile Grout Calculator is used to calculate the amount of epoxy tile grout that you need for a specific tile size and joint spacing.
Electrical Epoxy Calculator is used to calculate the amount of epoxy you will need to encapsulate electrical components.
Epoxy.com Conductive Flooring Calculator figures how much material you will need to install a conductive epoxy flooring system.
Is there another Epoxy.com product calculator that you would like to have here, send your suggestions to Norm Lambert – Epoxy.com Technical Director at firstname.lastname@example.org.
October 22, 2010
Epoxy.com Product #1 – ESD
Electro Static Dissipative Epoxy Coating
Ultra High Solids Epoxy Coating
Epoxy.com Product #1 – ESD (Electrostatic Dissipative) Epoxy Coating for ESD Flooring is an ultra high solids bis-A epoxy floor coating designed to provide
electrostatic control properties to various surfaces including concrete or other nonconductive substrates. The use of a conductive primer will transmit conductive readings through
Epoxy.com Product #1 – ESD (Electrostatic Dissipative) Epoxy Coating for ESD Flooring if applied no thicker than 15 mils.
Epoxy.com Product #1 – ESD (Electrostatic Dissipative) Epoxy Coating for ESD Flooring provides excellent bond to concrete as well as high impact and wear.
- Easy Application
- Dissipates a 5000 volt Charge to Zero in less than 0.1 Seconds @72°F
- Available in Static Dissipative Range of 1,000,000 to 1,000,000,000 ohms
per EOS/ESD Standards.
- Consistent Electrical Resistance Ratings When Tested at 10-500 Volts.
- High Gloss
- Good Abrasion Resistance.
- Easy to Clean..
Ultra High Solids Bis-A Epoxy Resin and Conductive Fillers.
Epoxy.com Product #1 – ESD (Electrostatic Dissipative) Epoxy Coating for ESD Flooring is available in Epoxy.com Colors listed to the right. Custom colors available as approved.
Surface preparation is considered to be the most important step of any
resinous flooring application. Improper surface preparation could turn what
seems to be a simple process into a lengthy, difficult repair. See Epoxy.com
Surface Preparation Guide for proper surface preparation
procedures. When in doubt you should always contact Epoxy.com Technical
Support with your questions.
Prime concrete surfaces with Epoxy.com Product #899
a rate of 250-300 SF per gallon and allow to dry to the touch.
Epoxy.com Product #1 – ESD (Electrostatic Dissipative) Epoxy Coating for ESD Flooring is normally spread with a
trowel or squeegee and back-rolled with a 3/8� medium nap roller. Care should be taken to minimize the entrapment of air caused by
Clean skin with soap and water. Tools and equipment should be cleaned with xylene or lacquer thinner.
Epoxy.com Product #1 – ESD (Electrostatic Dissipative) Epoxy Coating for ESD Flooring will yield 12-15 mils
when spread at 100-130 sq ft/gal. 15 mils is considered the maximum thickness.
After completing the application of Epoxy.com Product 100MR Moisture Tolerant Primer and Base Coat and the topcoats or floor covering system, the installer
should provide the owner with maintenance instructions relevant to the specific topcoats or floor covering. If floors become slippery due to
animal fats, oil, grease, or soap film, clean and rinse thoroughly.
Contact Epoxy.com Customer Service Department.
|Fungus & Bacteria Growth
||Will not support growth of fungus or bacteria
when subjected to mildew
||70-80 Shore D
|Bond Strength to Concrete
||Greater than 300psi (100% concrete failure)
|Thermal Shock Resistance
||100 in-lbs direct
||35-40 Min. (@73°F)
||14-16 hours (@73°F )
||5 days (@73°F.)
||Less than 50gm/l
|Weight per Gallon
||10.5-11 lbs per gal.
||Greater than 80
Contact Epoxy.com Technical Support Department
For more information Contact:
Director of Technical Support
Epoxy Systems, Inc
Available by Phone M-F 9AM-4PM Eastern Time (6 AM – 1 PM Pacific Time)
[Catalog of Products]
[Where to Start]
[Elastomeric Polyurethane Systems]
[Garage Floors] [High Temperature]
[Joint Systems & Sealants]
[Mortars / Grouts]
[Misc.] [Seamless Flooring]
[Who We Are]
[Tech Data Sheets in Acrobat Format]
[MSDS in Acrobat Format]
[Online Ordering Authorization Form]