Epoxy.com announces a new ESD Epoxy Product
New Epoxy Electrostic Dissipative (ESD) Epoxy Coating
Less Expensive, Easier to Use, More Durable
Epoxy.com Product #677
Electro Static Dissipative (ESD) /CONDUCTIVE COATING
DESCRIPTION
Epoxy.com Product #677 is a pigmented, water-based epoxy coating designed to achieve either an electro-static dissipative (ESD) finish or conductive finish by
modifying the underlying system components and thickness. Epoxy.com Product #677 has very low odor making it suitable for use in occupied
buildings and has high bond strength and adhesion to concrete and other surfaces.
ADVANTAGES
- Durable, Attractive, Chemical Resistant, Non-Porous, Light Reflective Finish.
- Low Odor during application and cure.
- Maintains Electrical Conductivity Performance over the Wear Life of the System
- Fast Dry and Re-coat Time.
- Easy Clean-up.
- Provides an ESD finish in the range of 1,000,000 to 1,000,000,000 ohms resistance when used over a non-conductive
primer/basecoat or a conductive finish in the range of 25,000 to 1,000,000 ohms resistance when used over a conductive primer/basecoat.
CONSIDERATIONS
- Substrate must be above 50°F and relative humidity below 85% for proper curing.
- Substrate must be free of dirt, waxes, curing agents and other foreign materials.
- Excessive moisture in the substrate will require a moisture vapor control treatment.
TYPICAL USES
Concrete floors and walls in electronic component assembly areas, data processing, military/aerospace, pharmaceutical plants,
hazardous industries (dust or explosion hazards). For use in any areas where the build-up of static electricity is a concern or a spark-proof floor is required.
APPLICATION
SURFACE PREPARATION
Surface Preparation is the most critical portion of any successful resinous flooring system application. All
substrates must be properly prepared and tested for moisture as outlined in Epoxy.com
Surface Preparation Guidelines.
INSTALLATION
Mix Part B of Epoxy.com Product #677 prior to combining. Mix 1 part Part A with 2 parts Part B. Epoxy.com Product #677 at a rate of 200 ft2
per gallon per coat with a short nap roller. Care should be taken to avoid
puddles. Two coats are necessary to insure uniform coverage.
Epoxy.com Product #677 Thin-Film ESD Epoxy Coating System 12-15 Mils(1,000,000-1,000,000,000 ohms)
| Material | Qty./ 1000 SF | Coverage |
|---|---|---|
| 1. Epoxy.com Product #899 Epoxy Primer | 4-5 gallons | 200-250 SF /gallon |
| 2. Epoxy.com Product #677 ESD/Conductive Epoxy Coating | 5 gallons | 200 SF /gallon |
| 3. Epoxy.com Product #677 ESD/Conductive Epoxy Coating | 5 gallons | 200 SF /gallon |
CLEAN-UP
Clean skin with soap and water. Tools and equipment should be cleaned with warm soapy water, xylene or lacquer thinner. Consult Material Safety Data for safety and health precautions.
COMPOSITION
Waterborne Epoxy Resin and Conductive Fillers
COVERAGE
Epoxy.com Product #677, when applied at 200 SF per gallon, yields 5.2 �to 6.0 mils dry film thickness.
TECHNICAL DATA
| Viscosity @ 75°F | 600-1000 CPS |
| Mixing Ratio | 1 Part A to 2 Parts B by Volume |
| Solids Content, by volume | 50-55% |
| Volatile Organic Content (VOC) | <20 gm/L |
| Bond Strength to Concrete | 400-500 psi (100% concretefailure |
| Weight per Gallon, mixed | 8.75-9.00 pounds per gallon, mixed |
CURE/DRY TIME
| Pot Life | 20-30 min. |
| Dry to touch | 6 hours @ 75°F |
| Recoat | 8-24 hours @ 75°F |
| Light Traffic | 24 hours @ 75°F |
| �H� Hardness | 2 days |
| �5-H� Hardness | 30 days |
AVAILABILITY
Contact Epoxy.com Customer Service Department at 321-206-1833
Maintenance
Remove animal fats, oil, grease or soap film promptly to reduce slipperiness. Epoxy.com Product #677 can be cleaned with neutral soaps and detergents.
If long periods of heavy traffic cause wear patterns reapply as need.
Anti-skid materials will reduce the effectiveness of the static dissipative
properties of this material. Do not use aggressive anti-skids. It is
impossible to get an accurate reading of the conductivity of the floor if
anti-skids are used.
Technical Services
Contact Epoxy.com Technical Support with your questions about this
product at 352-533-2167. Epoxy.com Technical Support Department can help you
with the selection, specification, installation, and maintenance of
Epoxy.com products, or visit http://www.epoxysystems.com.
Norm Lambert
President &
Director of Technical Support
Epoxy Systems, Inc
Available by Phone M-F 9AM-4PM Eastern Time (6 AM – 1 PM Pacific Time)
352-533-2167 (Voice)
352-465-3497 (fax)
norm@epoxy.com
[Home]
[Catalog of Products]
[Where to Start]
[Bonding Systems]
[Chip Floors]
[Chemical Resistance]
[Coatings]
[Conductive]
[Applications]
[Elastomeric Polyurethane Systems]
[Garage
Floors] [High Temperature]
[Industrial Floors]
[Injection]
[Joint Systems & Sealants]
[Mortars / Grouts]
[Novolac]
[Polymer Systems]
[Primers Sealers]
[Misc.] [Seamless Flooring]
[Waterproofing]
[Dealers Wanted]
[Installation Tips]
[Product Guide]
[Wood Filler]
[Who We Are]
[Guide Specs]
[Tech Data Sheets in Acrobat Format]
[MSDS in Acrobat Format]
Posted by Norm Lambert 
Epoxy.com News and Tips 